參數資料
型號: LM1894MTBD
廠商: National Semiconductor
文件頁數: 17/19頁
文件大?。?/td> 0K
描述: BOARD EVALUATION LM1894
標準包裝: 1
主要目的: 音頻,音頻處理
已用 IC / 零件: LM1894
已供物品:
相關產品: LM1894MX-ND - IC NOISE REDUCT SYS DYNAM 14SOIC
LM1894M-ND - IC DYNAM NOISE REDUCT SYS 14SOIC
SNAS551C – DECEMBER 1994 – REVISED APRIL 2013
External Component Guide
Component
Value
Purpose
C1
0.1
μF–100 μF
May be part of power supply, or may be added to suppress power supply
oscillation.
C2, C13
1
μF
Blocks DC, pin 2 and pin 13 are at DC potential of VS/2. C2, C13 form a low
frequency pole with 20k RIN.
C14
25
μF–100 μF
Improves power supply rejection.
C3, C12
0.0033
μF
Forms integrator with internal gm block and op amp. Sets bandwidth
conversion gain of 33 Hz/
μA of gm current.
C4, C11
1
μF
Output coupling capacitor. Output is at DC potential of VS/2.
C5
0.1
μF
Works with R1 and R2 to attenuate low frequency transients which could
disturb control path operation.
C6
0.001
μF
Works with input resistance of pin 6 to form part of control path frequency
weighting.
C8
0.1
μF
Combined with L8 and CL forms 19 kHz filter for FM pilot. This is only
required in FM applications(1).
L8, CL
4.7 mH, 0.015
μF
Forms 19 kHz filter for FM pilot. L8 is Toko coil CAN-1A185HM(1)(2).
C9
0.047
μF
Works with input resistance of pin 9 to form part of control path frequency
weighting.
C10
1
μF
Set attack and decay time of peak detector.
R1, R2
1 k
Ω
Sensitivity resistors set the noise threshold. Reducing attenuation causes
larger signals to be peak detected and larger bandwidth in main signal path.
Total value of R1 + R2 should equal 1 k
Ω.
R8
100
Ω
Forms RC roll-off with C8. This is only required in FM applications.
(1)
When FM applications are not required, pin 8 and pin 9 hook-up as follows:
(2)
Toko America Inc., 1250 Feehanville Drive, Mt. Prospect IL 60056
Circuit Operation
The LM1894 has two signal paths, a main signal path and a bandwidth control path. The main path is an audio
low pass filter comprised of a gm block with a variable current, and an op amp configured as an integrator. As
seen in Figure 11, DC feedback constrains the low frequency gain to AV = 1. Above the cutoff frequency of the
filter, the output decreases at
6 dB/oct due to the action of the 0.0033 μF capacitor.
The purpose of the control paths is to generate a bandwidth control signal which replicates the ear's sensitivity to
noise in the presence of a tone. A single control path is used for both channels to keep the stereo image from
wandering. This is done by adding the right and left channels together in the summing amplifier of Figure 11. The
R1, R2 resistor divider adjusts the incoming noise level to open slightly the bandwidth of the low pass filter.
Control path gain is about 60 dB and is set by the gain amplifier and peak detector gain. This large gain is
needed to ensure the low pass filter bandwidth can be opened by very low noise floors. The capacitors between
Copyright 1994–2013, Texas Instruments Incorporated
7
Product Folder Links: LM1894
相關PDF資料
PDF描述
A3DDH-3418G IDC CABLE - AKR34H/AE34G/AKR34H
M1GXK-2036J IDC CABLE - MCS20K/MC20G/X
BRC2016T1R5M INDUCTOR 1.5UH 1.1A 0806 SMD
M1FXK-2036J IDC CABLE - MCF20K/MC20G/X
REC3.5-0515DRW/R8/C CONV DC/DC 3.5W 4.5-9VIN +/-15VO
相關代理商/技術參數
參數描述
LM1894MX 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比(最小值): 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
LM1894MX/NOPB 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比(最小值): 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
LM1894N 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:OC White Company 功能描述:Dynamic Noise Reduction System 14-Pin PDIP Rail
LM1895 制造商:NSC 制造商全稱:National Semiconductor 功能描述:AUDIO POWE RAMPLIFIER
LM1895N 制造商:NSC 制造商全稱:National Semiconductor 功能描述:AUDIO POWE RAMPLIFIER