參數資料
型號: LM143
廠商: National Semiconductor Corporation
英文描述: High Voltage Operational Amplifier
中文描述: 高電壓運算放大器
文件頁數: 5/12頁
文件大?。?/td> 228K
代理商: LM143
Typical Performance Characteristics
(Continued)
Input Voltage Range
Output Voltage Swing
Voltage Gain
Supply Current
Input Current
Voltage Gain
TL/H/7783–3
Application Hints
(See AN-127)
The LM143 is designed for trouble free operation at any
supply voltage up to and including the guaranteed maximum
of
g
40V. Input overvoltage protection, both common-mode
and differential, is 100% tested and guaranteed at the maxi-
mum supply voltage. Furthermore, all possible high voltage
destructive modes during supply voltage turn-on have been
eliminated by design. As with most IC op amps, however,
certain precautions should be observed to insure that the
LM143 remains virtually blow-out proof.
Although output short circuits to ground or either supply can
be sustained indefinitely at lower supply voltages, these
short circuits should be of limited duration when operating at
higher supply voltages. Units can be destroyed by any com-
bination of high ambient temperature, high supply voltages,
and high power dissipation which results in excessive die
temperature. This is also true when driving low impedance
or reactive loads or loads that can revert to low impedance;
for example, the LM143 can drive most general purpose op
amps outside of the maximum input voltage range, causing
heavy current to flow and possibly destroying both devices.
Precautions should be taken to insure that the power sup-
plies never become reversed in polarityDeven under tran-
sient conditions. With reverse voltage, the IC will conduct
excessive current, fusing the internal aluminum intercon-
nects. Voltage reversal between the power supplies will al-
most always result in a destroyed unit.
In high voltage applications which are sensitive to very low
input currents, special precautions should be exercised. For
example, with high source resistances, care should be tak-
en to prevent the magnitude of the PC board leakage cur-
rents, although quite small, from approaching those of the
op amp input currents. These leakage currents become
larger at 125
§
C and are made worse by high supply volt-
ages. To prevent this, PC boards should be properly
cleaned and coated to prevent contamination and to pro-
vide protection from condensed water vapor when operat-
ing below 0
§
C. A guard ring is also recommended to signifi-
cantly reduce leakage currents from the op amp input pins
to the adjacent high voltage pins in the standard op amp pin
connection as shown in Figure 1. Figures 2, 3 and 4 show
how the guard ring is connected for the three most common
op amp configurations.
Finally, caution should be exercised in high voltage applica-
tions as electrical shock hazards are present. Since the
negative supply is connected to the case, users may inad-
vertantly contact voltages equal to those across the power
supplies.
The LM143 can be used as a plug-in replacement in most
general purpose op amp applications. The circuits present-
ed in the following section emphasize those applications
which take advantage of the unique high voltage abilities of
the LM143.
5
相關PDF資料
PDF描述
LM343 High Voltage Operational Amplifier
LM343H High Voltage Operational Amplifier
LM143H High Voltage Operational Amplifier
LM1572 1.5A, 500kHz Step-down Voltage Regulator
LM1577-12 SIMPLE SWITCHER Step-Up Voltage Regulator
相關代理商/技術參數
參數描述
LM143 WAF 制造商:Texas Instruments 功能描述:
LM143-155.52M 制造商:CONNOR-WINFIELD 制造商全稱:Connor-Winfield Corporation 功能描述:5.0x7.0mm Surface Mount LVDS Clock Oscillator Series
LM143CG WAF 制造商:Texas Instruments 功能描述:
LM143G WAF 制造商:Texas Instruments 功能描述:
LM143H 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Voltage Operational Amplifier