• <tfoot id="5ul50"><wbr id="5ul50"><th id="5ul50"></th></wbr></tfoot>
    <dfn id="5ul50"><dd id="5ul50"></dd></dfn>
    <code id="5ul50"><label id="5ul50"></label></code>
  • <big id="5ul50"><form id="5ul50"><small id="5ul50"></small></form></big>
    <dd id="5ul50"></dd>
  • <var id="5ul50"><input id="5ul50"><ul id="5ul50"></ul></input></var><li id="5ul50"><form id="5ul50"></form></li>
    參數資料
    型號: LKP5662-7EPD1TB1
    廠商: POWER-ONE INC
    元件分類: 電源模塊
    英文描述: 1-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    封裝: METAL, CASE K02, MODULE
    文件頁數: 22/23頁
    文件大小: 887K
    代理商: LKP5662-7EPD1TB1
    Cassette Style
    AC-DC Converters
    KP Series
    Edition 6/5.2000
    8/23
    Thermal Considerations
    If a converter is located in free, quasi-stationary air (con-
    vection cooling) at the indicated maximum ambient tem-
    perature
    TA max (see: table Temperature specifications) and
    is operated at its nominal input voltage and output power,
    the temperature measured at the
    Measuring point of case
    temperature TC (see: Mechanical Data) will approach the
    indicated value
    TC max after the warm-up phase. However,
    the relationship between
    TA and TC depends heavily on the
    conditions of operation and integration into a system. The
    thermal conditions are influenced by input voltage, output
    current, airflow and temperature of surrounding compo-
    nents and surfaces.
    TA max is therefore, contrary to TC max,
    an indicative value only.
    Caution: The installer must ensure that under all operat-
    ing conditions
    TC remains within the limits stated in the
    table:
    Temperature specifications.
    Notes: Sufficient forced cooling or an additional heat sink
    allows
    TA to be higher than 60
    °C (e.g. 70°C) if T
    C max is not
    exceeded.
    0
    0.1
    0.2
    0.3
    0.4
    0.5
    0.6
    0.7
    0.8
    TA min 50
    60
    70
    80
    90
    100
    Io/Io nom
    TA [°C]
    0.9
    1.00
    forced cooling
    convection cooling
    TC max
    -6 -7
    -6
    -7
    05143
    -5
    Fig. 7
    Output current derating versus temperature for -5, -6 and
    -7 units.
    Thermal Protection
    A temperature sensor generates an internal inhibit signal
    which disables the outputs if the case temperature exceeds
    TC max. The outputs are automatically re-enabled if the tem-
    perature drops below this limit.
    Output Protection
    Each output is protected against overvoltage which could
    occur due to a failure of the control circuit by means of a
    voltage suppressor diode which, under worst case condi-
    tions, may become a short circuit. The suppressor diodes
    are not designed to withstand externally applied over-
    voltages. Overload at any of the two outputs will cause a
    shut-down of both outputs. A red LED indicates the over-
    load condition.
    Efciency versus Load
    12
    3
    4
    0
    82
    70
    72
    74
    76
    78
    80
    Efficiency
    Io/Io nom
    Ui = 187 V AC
    Ui = 230 V AC
    05156
    84
    86
    88
    90
    Fig. 8
    Efciency versus load at Ui 230 V AC and 187 V AC
    Switching Frequency versus Load
    0.2
    0.4
    0.6
    0.8
    1
    0
    60
    0
    10
    20
    30
    40
    50
    Frequency [kHz]
    load [
    Io/Io nom]
    70
    80
    1.2
    05157
    Fig. 9
    Switching frequency versus load. (The boost converter at
    the input stage has a xed frequency of 100 kHz)
    Parallel or Series Connection of Units
    Units with equal nominal output voltage can be connected
    in parallel without any precautions using option T.
    With option T (current sharing), all units share the current
    approximately equally.
    Main and second outputs can be connected in series with
    any other (similar) output.
    Note:
    – Parallel connection of double output units should always
    include both, main and second output to maintain good
    regulation of both outputs.
    – Not more than 3 units should be connected in parallel.
    – Series connection of second outputs without involving
    their main outputs should be avoided as regulation may
    be poor.
    – The maximum output current is limited by the output with
    the lowest current limitation if several outputs are con-
    nected in series.
    相關PDF資料
    PDF描述
    LKP5661-5ERD5TB1 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    LKP5662-7EPD2TB1 1-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    LKP5660-6EPD6TB1 1-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    LKP5740-6ERD6TB1 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    LKP5741-5ERD5TB1 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    相關代理商/技術參數
    參數描述
    LKP5662-7R 制造商:Power-One 功能描述:AC/DC PS DUAL-OUT 24V/24V 280W 15PIN - Bulk
    LKP5663-7ERG 制造商:Power-One 功能描述:
    LKP5740-6R 制造商:Power-One 功能描述:AC/DC PS SGL-OUT 50.5V TO 56.5V 4.5A 254W - Bulk
    LKP5740-7R 功能描述:線性和開關式電源 Euro-Cassette 231W (25.68V) Battery Charger RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓(通道 1):20 V 輸出電流(通道 1):40 A 商用/醫用: 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:Rack 長度: 寬度: 高度:
    LKP5741-5R 制造商:Power-One 功能描述:AC/DC PS SGL-OUT 51.36V 5A 280W 15PIN - Bulk