<menuitem id="kqquk"></menuitem>
  • <code id="kqquk"></code>
  • <form id="kqquk"><meter id="kqquk"></meter></form>
    <table id="kqquk"><nobr id="kqquk"><optgroup id="kqquk"></optgroup></nobr></table><table id="kqquk"><tbody id="kqquk"></tbody></table><menuitem id="kqquk"><dl id="kqquk"></dl></menuitem>
  • 參數資料
    型號: LK5320-7EB1
    廠商: POWER-ONE INC
    元件分類: 電源模塊
    英文描述: 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
    封裝: HEAT SINK, METAL, CASE K02
    文件頁數: 17/28頁
    文件大小: 1215K
    代理商: LK5320-7EB1
    K Series
    AC-DC Converters >100 Watt
    Rugged Environment
    Edition 4/4.99
    24/28
    MELCHER
    The Power Partners.
    Vo1+
    Vo1–
    D
    UD
    ID
    Rp
    Input
    11007
    NPN output (D5...DD):
    Connector pin D is internally connected via the collector-
    emitter path of a NPN transistor to the negative potential of
    output 1.
    UD
    < 0.4 V (logic low) corresponds to a monitored
    voltage level (
    Ui and/or Uo1)
    > U
    t + Uh. The current ID
    through the open collector should not exceed 20 mA. The
    NPN output is not protected against external overvoltages.
    UD should not exceed 40 V.
    Ui, Uo1 status
    D output,
    UD
    Ui or Uo1 < Ut
    high, H,
    ID ≤ 25 A at UD = 40 V
    Ui and Uo1 > Ut + Uh
    low, L,
    UD ≤ 0.4 V at ID = 20 mA
    Fig. 37
    Option D5...DD: NPN output, Uo1
    ≤ 40 V, I
    D
    ≤ 20 mA
    Table 19: D-output logic signals
    Version of D
    Ui < Ut resp. Uo < Ut
    Ui > Ut + Uh resp. Uo > Ut
    Conguration
    D1, D2, D3, D4, D0
    low
    high
    JFET
    D5, D6, D7, D8, D9, DD
    high
    low
    NPN
    Option D Undervoltage monitor
    The input and/or output undervoltage monitoring circuit op-
    erates independently of the built-in input undervoltage lock-
    out circuit. A logic "low" (JFET output) or "high" signal (NPN
    output) is generated at pin 20 as soon as one of the moni-
    tored voltages drops below the preselected threshold level
    Ut. The return for this signal is Vo1–. The D output reco-
    vers when the monitored voltage(s) exceed(s)
    Ut + Uh. The
    Table 18: Undervoltage monitoring functions
    Output type
    Monitoring
    Minimum adjustment range
    Typical hysteresis
    Uho [% of Ut]
    JFET
    NPN
    U i
    Uo1
    of threshold level
    U t
    for
    U t min...U t max
    Uti
    Uto
    Uho
    D1
    D5
    no
    yes
    -
    3.5...40 V 1
    2.5...0.6
    D2
    D6
    yes
    no
    355 V DC 4
    --
    D3
    D7
    yes
    355 V DC 4
    (0.95...0.985
    Uo1) 2
    "0"
    D4
    D8
    no
    yes
    -
    (0.95...0.985
    Uo1) 2
    "0"
    D0
    D9
    no
    yes
    -
    3.5...40 V 3
    2.5...0.6
    yes
    355 V DC 4
    3.5...40 V 3
    2.5...0.6
    DD
    yes
    355 V DC4
    3.5...40 V 1
    2.5...0.6
    1 Threshold level adjustable by potentiometer
    2 Fixed value. Tracking if Uo1 adjusted via R-input, option P or sense lines.
    3 The threshold level permanently adjusted according to customer specication
    ±2% at 25°C. Any value within the specied range is
    basically possible but causes a special type designation in addition to the standard option designations (D0/D9)!
    4 Option D monitors the boost regulator output voltage. The trigger level is adjusted in the factory to 355 V DC.
    threshold level
    Uti is adjusted in the factory. The threshold
    level
    Uto is either adjusted by a potentiometer, accessible
    through a hole in the front cover, or factory adjusted to a
    xed value specied by the customer.
    Option D exists in various versions D0...DD as shown in the
    following table.
    Vo1+
    Vo1–
    D
    UD
    ID
    Rp
    Input
    11006
    Fig. 36
    Option D0...D4: JFET output, ID
    ≤ 2.5 mA
    JFET output (D0…D4):
    Connector pin D is internally connected via the drain-
    source path of a JFET (self-conducting type) to the nega-
    tive potential of output 1.
    UD
    ≤ 0.4 V (logic low) corresponds
    to a monitored voltage level (
    Ui and/or Uo1)
    <U
    t. The cur-
    rent
    ID through the JFET should not exceed 2.5 mA. The
    JFET is protected by a 0.5 W Zener diode of 8.2 V against
    external overvoltages.
    Ui, Uo1 status
    D output,
    UD
    Ui or Uo1 < Ut
    low, L,
    UD ≤ 0.4 V at ID = 2.5 mA
    Ui and Uo1 > Ut + Uh
    high, H,
    ID ≤ 25 A at UD = 5.25 V
    相關PDF資料
    PDF描述
    LK5320-7ERD3B1 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
    LK5320-7ETB1 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
    LK5320-7PD9T 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
    LK5320-7T 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
    LK5320-9D8T 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
    相關代理商/技術參數
    參數描述
    LK5320-7R 功能描述:線性和開關式電源 Euro-Cassette 144W (2x 12V) RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓(通道 1):20 V 輸出電流(通道 1):40 A 商用/醫用: 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:Rack 長度: 寬度: 高度:
    LK5320-9ER 制造商:Power-One 功能描述:AC/DC PS DUAL-OUT 12V/12V 6A/6A 280W 15PIN - Bulk
    LK-54H-SS18(LF)(SN) 制造商:JST Manufacturing 功能描述:
    LK5540-7R 功能描述:線性和開關式電源 150W 15V 5A OUT AC-DC CONVERTER RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓(通道 1):20 V 輸出電流(通道 1):40 A 商用/醫用: 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:Rack 長度: 寬度: 高度:
    LK5540-9ER 制造商:Power-One 功能描述:ACDC - Bulk