- 您現在的位置：買賣IC網 > PDF目錄43970 > LK2660-9D3 (POWER-ONE INC) 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LK2660-9D3 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| 封裝： | HEAT SINK, METAL, CASE K02, MODULE |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 1027K |
| 代理商： | LK2660-9D3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁
Cassette Style
AC-DC Converters
K Series
Edition 5/5.2000
8/26
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for –7 and –9.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diodes
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Uo1d
t d
Ur
t
Uo2d
<10
s
<10
s
Uo1
Uo2
Io1/Io1 nom
0
0.5
1
Io2/Io2 nom
05072
Fig. 8
Control deviation of uo1/2 d vs. dynamic load change.
Output Voltage Regulation of Single or Double Output
Modules with Outputs1 and 2 Connected in Series
Uo
Uo nom
0.98
0.5
0
0.5
1.0
Io1
IoL
Io
Io nom
05068
Fig. 9
Uo1 versus Io1 (typ.) of single output units
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Not more than 5 units should be connected in parallel.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
相關PDF資料 |
PDF描述 |
|---|---|
| LK2660-9RD1TB2 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK2660-9RD6TB2 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1001-7EPD2B2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1001-9PD2B2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1001-9PDD | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LK2660-9ER | 制造商:Power-One 功能描述:ACDC - Bulk |
| LK28 | 制造商:Molex 功能描述:BOX, LINE FEED 4D/PRF |
| LK28-LAS-F1-Z/31/116 | 制造商:PEPPERL+FUCHS 功能描述:SENSOR, PHOTOELECTRIC, UNIVERSAL STYLE, THRU-BEAM RECEIVER, SENSING DIS 300M 制造商:PEPPERL+FUCHS 功能描述:Photoelectric (Automation) |
| LK2A | 制造商:HellermannTyton 功能描述: |
| LK2A-BLACK | 制造商:HellermannTyton 功能描述:CABLE TIE HEAVYDUTY BLACK 270MM 制造商:HellermannTyton 功能描述:CABLE TIE, HEAVYDUTY, BLACK, 270MM 制造商:HELLERMANN TYTON 功能描述:CABLE TIE, HEAVYDUTY, BLACK, 270MM; Cable Tie Length:270mm; Cable Tie Width:4.6mm; Cable Tie Material:Nylon 6.6 (Polyamide 6.6); Cable Tie Colour:Black; Tensile Strength N/m2:225N/mm2; Cable Bundle Diameter Min:5mm; Cable Bundle ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。
