• <dl id="tad9f"><menuitem id="tad9f"><abbr id="tad9f"></abbr></menuitem></dl>
      參數資料
      型號: LK1301-7PD3TB2
      元件分類: 電源模塊
      英文描述: 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
      封裝: METAL, CASE K02, MODULE
      文件頁數: 2/26頁
      文件大?。?/td> 601K
      代理商: LK1301-7PD3TB2
      Cassette Style
      150 Watt AC-DC Converters
      K Series
      Edition 01/01.2001
      10/26
      0
      t
      0
      Inhibit
      1
      0.1
      1
      Uo/Uo nom
      tr
      tf
      06001
      Fig. 15
      Output response as a function of inhibit control
      Auxiliary Functions
      i Inhibit for Remote On and Off
      Note: With open i input: Output is disabled (
      Uo = off).
      The outputs of the module may be enabled or disabled by
      means of a logic signal (TTL, CMOS, etc.) applied between
      the inhibit input i and the negative pin of output 1 (Vo1–). In
      systems with several units, this feature can be used, for ex-
      ample, to control the activation sequence of the converters.
      If the inhibit function is not required, connect the inhibit pin
      18 to pin 14 to enable the outputs (active low logic, fail
      safe). For output response refer to:
      Hold-up Time and Out-
      put Response.
      Vi+
      Vi–
      Vo–
      i
      Vo+
      Iinh
      Uinh
      06031
      1.6
      0.8
      0
      –0.8
      –50
      Uinh [V]
      Iinh [mA]
      –30
      0
      –10
      10
      30
      50
      2.0
      1.2
      0.4
      –0.4
      Uinh = 0.8 V
      Uo = on
      Uo = off
      Uinh = 2.4 V
      06032
      Fig. 13
      Definition of Uinh and Iinh.
      Fig. 14
      Typical inhibit current Iinh versus inhibit voltage Uinh
      Table 5: Inhibit characteristics
      Characteristic
      Conditions
      min
      typ
      max Unit
      Uinh Inhibit
      Uo = on
      Ui min…Ui max
      –50
      0.8
      V
      voltage
      Uo = off
      2.4
      50
      Iinh
      Inhibit current
      Uinh = 0
      –400
      A
      tr
      Rise time
      30
      ms
      tf
      Fall time
      depending on
      Io
      Sense Lines
      (Only for single output units 5.1 V, 12 V, 15 V, 24 V)
      This feature enables for compensation of voltage drops
      across the connector contacts and if necessary, across the
      load lines. If the sense lines are connected at the load
      rather than directly at the connector, the user should ensure
      that
      Uo max (between Vo1+ and Vo1–) is not exceeded. We
      recommend connecting the sense lines directly at the fe-
      male connector.
      For further information, please refer to:
      Application Notes .
      To ensure correct operation, both sense lines (S+ and S–)
      should be connected to their respective power outputs
      (Vo1+ and Vo1–) and the voltage difference between any
      sense line and its respective power output pin (as meas-
      ured on the connector) should not exceed the following val-
      ues:
      Table 6: Maximum Voltage compensation allowed using
      sense lines
      Output
      Total voltage difference
      Voltage difference
      voltage
      between sense lines and
      between
      their respective outputs
      Vo– and S–
      5.1 V
      <0.5 V
      <0.25 V
      12 V, 15 V
      <1.0 V
      <0.25 V
      If the output voltages are increased above
      Uo nom via R-in-
      put control, option P setting, remote sensing or option T, the
      output currents must be reduced accordingly so that
      Po nom is not exceeded.
      Important: The output terminals Vo1+ and Vo1– must
      always be connected to the load before connecting the
      sense lines S+ and S–, otherwise the unit will be dam-
      aged.
      相關PDF資料
      PDF描述
      LK1301-9ERD0TB2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
      LK1501-7ERD9B2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
      LK1501-9EPD8B2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
      LK1501-9RD7B2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
      LK1601-9EPD9B2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
      相關代理商/技術參數
      參數描述
      LK1301-7R 功能描述:線性和開關式電源 Euro-Cassette 150W (12V) RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓(通道 1):20 V 輸出電流(通道 1):40 A 商用/醫用: 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:Rack 長度: 寬度: 高度:
      LK1301-9ER 制造商:Power-One 功能描述:AC/DC Power Supply Single-OUT 12V 12A 150W 15-Pin 制造商:Power-One 功能描述:ACDC - Bulk
      LK1301-9ERB 制造商:Power-One 功能描述:ACDC - Bulk
      LK-14 制造商:Shinagawa Shoko 功能描述:
      LK14 Y/R 制造商:Altech Corporation 功能描述: