- 您現在的位置：買賣IC網 > PDF目錄43919 > LIS3DHTR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF資料下載
參數資料
| 型號： | LIS3DHTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封裝： | 3 X 3 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件頁數： | 29/42頁 |
| 文件大?。?/td> | 689K |
| 代理商： | LIS3DHTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LIS3DH
Registers description
Doc ID 17530 Rev 1
35/42
Content of this register is loaded at boot.
Write operation at this address is possible only after system boot.
Difference between AOI-6D = ‘01’ and AOI-6D = ‘11’.
AOI-6D = ‘01’ is movement recognition. An interrupt is generate when orientation move from
unknown zone to known zone. The interrupt signal stay for a duration ODR.
AOI-6D = ‘11’ is direction recognition. An interrupt is generate when orientation is inside a
known zone. The interrupt signal stay until orientation is inside the zone.
8.22
INT1_SRC (31h)
ZLIE/
ZDOWNE
Enable interrupt generation on Z low event or on Direction recognition. Default
value: 0 (0: disable interrupt request;1: enable interrupt request)
YHIE/
YUPE
Enable interrupt generation on Y high event or on Direction recognition. Default
value: 0 (0: disable interrupt request; 1: enable interrupt request.)
YLIE/
YDOWNE
Enable interrupt generation on Y low event or on Direction recognition. Default
value: 0 (0: disable interrupt request; 1: enable interrupt request.)
XHIE/
XUPE
Enable interrupt generation on X high event or on Direction recognition. Default
value: 0 (0: disable interrupt request; 1: enable interrupt request.)
XLIE/XDOWNE Enable interrupt generation on X low event or on Direction recognition. Default
value: 0 (0: disable interrupt request; 1: enable interrupt request.)
Table 48.
Interrupt mode
AOI
6D
Interrupt mode
0
OR combination of interrupt events
0
1
6 direction movement recognition
1
0
AND combination of interrupt events
1
6 direction position recognition
Table 47.
INT1_CFG description
Table 49.
INT1_SRC register
0
IA
ZH
ZL
YHYLXHXL
Table 50.
INT1_SRC description
IA
Interrupt active. Default value: 0
(0: no interrupt has been generated; 1: one or more interrupts have been generated)
ZH
Z high. Default value: 0
(0: no interrupt, 1: Z High event has occurred)
ZL
Z low. Default value: 0
(0: no interrupt; 1: Z Low event has occurred)
YH
Y high. Default value: 0
(0: no interrupt, 1: Y High event has occurred)
相關PDF資料 |
PDF描述 |
|---|---|
| LIS3DH | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| LIS3L02AL | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| LIS3L02ALTR | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| LIS3L02AQ5TR | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L02AQ5 | SPECIALTY ANALOG CIRCUIT, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS3DSH | 功能描述:加速計 - 板上安裝 MEMS 3-Axis Nano 1.71 to 3.6V 1.6kHz RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3DSHTR | 功能描述:加速計 - 板上安裝 MEMS 3-Axis Nano 1.71 to 3.6V 1.6kHz RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3L02AL | 功能描述:加速計 - 板上安裝 3-axis +/-2g Linear MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3L02AL | 制造商:STMicroelectronics 功能描述:ACCELEROMETER 3 AXIS LGA-8 302 |
| LIS3L02ALETR | 制造商:ST 功能描述:MEMS INERTIAL SENSOR: 3-Axis - ??2g/??6g LINEAR ACCELEROMETER |
發布緊急采購，3分鐘左右您將得到回復。