參數資料
型號: LIS35DETR
廠商: STMICROELECTRONICS
元件分類: 模擬信號調理
英文描述: SPECIALTY ANALOG CIRCUIT, PBGA14
封裝: 3 X 5 MM, 0.92 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, LGA-14
文件頁數: 7/39頁
文件大小: 650K
代理商: LIS35DETR
LIS35DE
Functionality
Doc ID 15594 Rev 1
15/39
3
Functionality
The LIS35DE is a ultracompact, low-power, digital output 3-axis linear accelerometer
packaged in a LGA package. The complete device includes a sensing element and an IC
interface able to take the information from the sensing element and to provide a signal to the
external world through an I2C/SPI serial interface.
3.1
Sensing element
A proprietary process is used to create a surface micro-machined accelerometer. The
technology allows to carry out suspended silicon structures which are attached to the
substrate in a few points called anchors and are free to move in the direction of the sensed
acceleration. To be compatible with the traditional packaging techniques a cap is placed on
top of the sensing element to avoid blocking the moving parts during the moulding phase of
the plastic encapsulation.
When an acceleration is applied to the sensor the proof mass displaces from its nominal
position, causing an imbalance in the capacitive half-bridge. This imbalance is measured
using charge integration in response to a voltage pulse applied to the sense capacitor.
At steady state the nominal value of the capacitors are few pF and when an acceleration is
applied the maximum variation of the capacitive load is in fF range.
3.2
IC interface
The complete measurement chain is composed by a low-noise capacitive amplifier which
converts into an analog voltage the capacitive unbalancing of the MEMS sensor and by
analog-to-digital converters.
The acceleration data may be accessed through an I2C/SPI interface thus making the
device particularly suitable for direct interfacing with a microcontroller.
The LIS35DE features a Data-Ready signal (RDY) which indicates when a new set of
measured acceleration data is available thus simplifying data synchronization in the digital
system that uses the device.
The LIS35DE may also be configured to generate an inertial Wake-Up and Free-Fall
interrupt signal accordingly to a programmed acceleration event along the enabled axes.
Both Free-Fall and Wake-Up can be available simultaneously on two different pins.
3.3
Factory calibration
The IC interface is factory calibrated for sensitivity (So) and Zero-g level (Off).
The trimming values are stored inside the device by a non volatile memory. Any time the
device is turned on, the trimming parameters are downloaded into the registers to be used
during the normal operation. This allows the user to use the device without further
calibration.
相關PDF資料
PDF描述
LIS3L02AQ3TR SPECIALTY ANALOG CIRCUIT, PQCC44
LIS3L02AQ3 SPECIALTY ANALOG CIRCUIT, PQCC44
LIS3L06AL SPECIALTY ANALOG CIRCUIT, PBGA8
LIS3LV02DQ-TR SPECIALTY ANALOG CIRCUIT, PQCC28
LIS3LV02DQ SPECIALTY ANALOG CIRCUIT, PQCC28
相關代理商/技術參數
參數描述
LIS-3-6 制造商:TDK-Lambda Corporation 功能描述:15W AC To DC Switching Power Supply - 95-132V/187-265V in - 6V 2.5A out
LIS3DETR 制造商:STMicroelectronics 功能描述: 制造商:STMicroelectronics 功能描述:SADA_MEMS digital output motion sensor, ultra low-power high performance 3-axes
LIS3DH 功能描述:加速計 - 板上安裝 MEMS Ultra Low-Power 3-Axes "Nano" RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS3DHHTR 功能描述:ACCELEROMETER 3-AXIS 16LGA 制造商:stmicroelectronics 系列:MEMS 零件狀態:在售 類型:數字 軸:X,Y,Z 加速度范圍:±2.5g 靈敏度(LSB/g):13157(±2.5g) 靈敏度(mV/g):- 帶寬:235Hz ~ 440Hz 輸出類型:SPI 電壓 - 電源:1.71 V ~ 3.6 V 特性:溫度傳感器 工作溫度:-40°C ~ 85°C(TA) 安裝類型:表面貼裝 封裝/外殼:16-LGA 供應商器件封裝:16-CCLGA(5x5) 標準包裝:1
LIS3DHTR 功能描述:加速計 - 板上安裝 MEMS Ultra Low-Power 3-Axes "Nano" RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C