- 您現在的位置：買賣IC網 > PDF目錄43919 > LIS331ALTR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, QCC16 PDF資料下載
參數資料
| 型號： | LIS331ALTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC16 |
| 封裝： | 3 X 3 MM, 1 MM HEIGHT, GREEN, LGA-16 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 190K |
| 代理商： | LIS331ALTR |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Mechanical and electrical specifications
LIS331AL
10/16
over lifetime. The Zero-g level tolerance describes the range of Zero-g levels of a population
of sensors.
Self Test allows to test the mechanical and electric part of the sensor, allowing the seismic
mass to be moved by means of an electrostatic test-force. The Self Test function is off when
the ST pin is connected to GND. When the ST pin is tied at Vdd an actuation force is applied
to the sensor, simulating a definite input acceleration. In this case the sensor outputs will
exhibit a voltage change in their DC levels which is depending on the Supply Voltage
through the device sensitivity. When ST is activated, the device output level is given by the
algebraic sum of the signals produced by the acceleration acting on the sensor and by the
electrostatic test-force. If the output signals change within the amplitude specified inside
Table 3, than the sensor is working properly and the parameters of the interface chip are
within the defined specification.
Output impedance describes the resistor inside the output stage of each channel. This
resistor is part of a filter consisting of an external capacitor of at least 2.5nF and the internal
resistor. Due to the resistor level, only small inexpensive external capacitors are needed to
generate low corner frequencies. When interfacing with an ADC it is important to use high
input impedance input circuitries to avoid measurement errors. Note that the minimum load
capacitance forms a corner frequency close to the resonance frequency of the sensor. In
general the smallest possible bandwidth for a particular application should be chosen to get
the best results.
相關PDF資料 |
PDF描述 |
|---|---|
| LIS331DLF | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS331DLHTR | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS331DLMTR | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS331DL | MOTION SENSOR, PQCC16 |
| LIS331DLTR | MOTION SENSOR, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS331DL | 功能描述:加速計 - 板上安裝 MEMS MOTION SENSOR 3-AXIS RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS331DL | 制造商:STMicroelectronics 功能描述:ACCELEROMETER, MEMS, 3-AXIS, DIGITAL O/P, LGA-16; MEMS Sensor Output:Digital; Measurement Axis:X, Y, Z; Acceleration Range: 2g, 8g; Supply Voltage Min:2.16V; Supply Voltage Max:3.6V; Sensor Case Style:LGA; No. of Pins:16 ;RoHS Compliant: No |
| LIS331DL_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS motion sensor 3-axis - 【2g/【8g smart digital output -nano-accelerometer |
| LIS331DLF | 功能描述:加速計 - 板上安裝 DGTL OUTPT MTN SEN MEMS ULTRA LO PWR RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS331DLFTR | 功能描述:加速計 - 板上安裝 DGTL OUTPT MTN SEN MEMS ULTRA LO PWR RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發布緊急采購，3分鐘左右您將得到回復。