參數資料
型號： LIS302DLTR8
廠商： STMICROELECTRONICS
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PQCC14
封裝： 3 X 5 MM, 0.92 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, TLGA-14
文件頁數： 20/42頁
文件大?。?/td> 602K
代理商： LIS302DLTR8
LIS302DL
Register description
27/42
Zen bit enables the generation of Data Ready signal for Z-axis measurement channel when
set to 1. The default value is 1.
Yen bit enables the generation of Data Ready signal for Y-axis measurement channel when
set to 1. The default value is 1.
Xen bit enables the generation of Data Ready signal for X-axis measurement channel when
set to 1. The default value is 1.
7.3
CTRL_REG2 (21h)
SIM bit selects the SPI Serial Interface Mode. When SIM is ‘0’ (default value) the 4-wire
interface mode is selected. The data coming from the device are sent to SDO pad. In 3-wire
interface mode output data are sent to SDA_SDI pad.
BOOT bit is used to refresh the content of internal registers stored in the flash memory
block. At the device power up the content of the flash memory block is transferred to the
internal registers related to trimming functions to permit a good behavior of the device itself.
If for any reason the content of trimming registers was changed it is sufficient to use this bit
to restore correct values. When BOOT bit is set to ‘1’ the content of internal flash is copied
inside corresponding internal registers and it is used to calibrate the device. These values
are factory trimmed and they are different for every accelerometer. They permit a good
behavior of the device and normally they have not to be changed. At the end of the boot
process the BOOT bit is set again to ‘0’.
FDS bit enables (FDS=1) or bypass (FDS=0) the high pass filter in the signal chain of the
sensor
HP_coeff[2:1]. These bits are used to configure high-pass filter cut-off frequency ft.
Table 20.
CTRL_REG2 (21h) register
SIM
BOOT
--
FDS
HP_FF_W
U2
HP_FF_W
U1
HP_coeff2
HP_coeff1
Table 21.
CTRL_REG2 (21h) register description
SIM
SPI Serial Interface Mode selection. Default value: 0
(0: 4-wire interface; 1: 3-wire interface)
BOOT
Reboot memory content. Default value: 0
(0: normal mode; 1: reboot memory content)
FDS
Filtered Data Selection. Default value: 0
(0: internal filter bypassed; 1: data from internal filter sent to output register)
HP FF_WU2
High Pass filter enabled for FreeFall/WakeUp # 2. Default value: 0
(0: filter bypassed; 1: filter enabled)
HPFF_WU1
High Pass filter enabled for Free-Fall/Wake-Up #1. Default value: 0
(0: filter bypassed; 1: filter enabled)
HP coeff2
HP coeff1
High pass filter cut-off frequency configuration. Default value: 00
(See table below)
相關PDF資料
PDF描述
LIS331ALTR SPECIALTY ANALOG CIRCUIT, QCC16
LIS331DLF SPECIALTY ANALOG CIRCUIT, PBCC16
LIS331DLHTR SPECIALTY ANALOG CIRCUIT, PBCC16
LIS331DLMTR SPECIALTY ANALOG CIRCUIT, PBCC16
LIS331DL MOTION SENSOR, PQCC16
相關代理商/技術參數
參數描述
LIS302DLTR-CUT TAPE 制造商:ST 功能描述:LIS302DL Series 3 Axis ?/? g 3.3 V Digital Output Piccolo Accerometer - LGA-14
LIS302SG 功能描述:加速計 - 板上安裝 MEMS MOTION SENSOR 3 AXIS +/-2g Piccolo RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS302SGTR 功能描述:加速計 - 板上安裝 MEMS motion sensor 3-axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS-3-15 制造商:TDK-Lambda Corporation 功能描述:15W AC To DC Switching Power Supply - 95-132V/187-265V in - 15V 1A out
LIS-3-20 制造商:TDK-Lambda Corporation 功能描述:15W AC To DC Switching Power Supply - 95-132V/187-265V in - 20V 0.75A out
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*