- 您現在的位置：買賣IC網 > PDF目錄358041 > LIS2L02AS (意法半導體) INERTIAL SENSOR: 2Axis - 2g/6g LINEAR ACCELEROMETER PDF資料下載
參數資料
| 型號： | LIS2L02AS |
| 廠商： | 意法半導體 |
| 元件分類： | 加速度傳感器 |
| 英文描述： | INERTIAL SENSOR: 2Axis - 2g/6g LINEAR ACCELEROMETER |
| 中文描述： | 慣性傳感器：2Axis - 2g/6g線性加速度計 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 120K |
| 代理商： | LIS2L02AS |
LIS2L02AQ
4/6
Figure 1. Equivalent electrical circuit
1.2 IC Interface
The complete signal processing uses a fully differential structure, while the final stage converts the differential
signal into a single-ended one to be compatible with the external world.
The first stage is a low-noise capacitive amplifier that implements a Correlated Double Sampling (CDS) at its
output to cancel the offset and the 1/f noise. The produced signal is then sent to two different S&Hs, one for
each channel, and made available to the outside.
The low noise input amplifier operates at 200 kHz while the two S&Hs operate at a sampling frequency of 66
kHz. This allows a large oversampling ratio, which leads to in-band noise reduction and to an accurate output
waveform.
All the analog parameters (output offset voltage and sensitivity) are ratiometric to the voltage supply. Increasing
or decreasing the voltage supply, the sensitivity and the offset will increase or decrease linearly. The feature
provides the cancellation of the error related to the voltage supply along an analog to digital conversion chain.
1.3 Factory calibration
The IC interface is factory calibrated to provide to the final user a device ready to operate. The parameters which
are trimmed are: gain, offset, common mode and internal clock frequency.
The trimming values are stored inside the device by a poly-fuse structure. Any time the device is turned on, the
memorized bits are downloaded into the registers to be employed during the normal operation. The poly-fuse
approach allows the final user to utilize the device without any need for further calibration
C
s1x
C
s2x
C
ps1
C
ps2
C
pr
R
s2
R
s1
R
r
S1x
rot
S2x
C
s1y
C
s2y
C
ps1
C
ps2
C
pr
R
s2
R
s1
R
r
S1y
S2y
相關PDF資料 |
PDF描述 |
|---|---|
| LK1608100K | 1 ELEMENT, 10 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| LK1608R47M | 1 ELEMENT, 0.47 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| LK1608R56K | 1 ELEMENT, 0.56 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| LK2125R68M | 1 ELEMENT, 0.68 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| LK3216100M | 1 ELEMENT, 10 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS2L02AS4 | 功能描述:加速計 - 板上安裝 2-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS2L02AS4-TR | 功能描述:加速計 - 板上安裝 LINEAR ACCELEROMETER 2 AXIS 2G/6G RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS2L02AS-TR | 制造商:STMicroelectronics 功能描述:LINEAR ACCELEROMETER 2 AXIS - Tape and Reel |
| LIS2L06A | 制造商:STMicroelectronics 功能描述:ACCELERATION SENSOR IC |
| LIS2L06AL | 功能描述:加速計 - 板上安裝 2-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發布緊急采購，3分鐘左右您將得到回復。