- 您現在的位置：買賣IC網 > PDF目錄384593 > LIS2L02AS4 (意法半導體) MEMS INERTIAL SENSOR: 2-Axis - 【2g/【6g LINEAR ACCELEROMETER PDF資料下載
參數資料
| 型號： | LIS2L02AS4 |
| 廠商： | 意法半導體 |
| 英文描述： | MEMS INERTIAL SENSOR: 2-Axis - 【2g/【6g LINEAR ACCELEROMETER |
| 中文描述： | MEMS慣性傳感器：兩軸- 【2克/【六克線性加速度計 |
| 文件頁數： | 5/14頁 |
| 文件大小： | 167K |
| 代理商： | LIS2L02AS4 |
5/14
LIS2L02AS4
3.1 Terminology
3.1.1 Sensitivity
Describes the gain of the sensor and can be determined by applying 1g acceleration to it. As the sensor
can measure DC accelerations this can be done easily by pointing the axis of interest towards the center
of the earth, note the output value, rotate the sensor by 180 degrees (point to the sky) and note the output
value again thus applying
±
1g acceleration to the sensor. Subtracting the larger output value from the
smaller one and dividing the result by 2 will give the actual sensitivity of the sensor. This value changes
very little over temperature (see sensitivity change vs. temperature) and also very little over time. The Sen-
sitivity Tolerance describes the range of Sensitivities of a large population of sensors.
3.1.2 Zero-g level
Describes the actual output signal if there is no acceleration present. A sensor in a steady state on an
horizontal surface will measure 0g in X axis and 0g in Y axis whereas the Z axis will measure +1g. The
output is ideally for a 3.3V powered sensor Vdd/2 = 1650mV. A deviation from ideal 0-g level (1650mV in
this case) is called Zero-g offset. Offset of precise MEMS sensors is to some extend a result of stress to
the sensor and therefore the offset can slightly change after mounting the sensor onto a printed circuit
board or exposing it to extensive mechanical stress. Offset changes little over temperature - see "Zero-g
Level Change vs. Temperature" - the Zero-g level of an individual sensor is very stable over lifetime. The
Zero-g level tolerance describes the range of zero-g levels of a population of sensors.
3.1.3 Self Test
Self Test allows to test the mechanical and electric part of the sensor, allowing the seismic mass to be
moved by means of an electrostatic test-force. The Self Test function is off when the ST pin is connected
to GND. When the ST pin is tied at Vdd an actuation force is applied to the sensor, simulating a definite
input acceleration. In this case the sensor outputs will exhibit a voltage change in their DC levels which is
related to the selected full scale and depending on the Supply Voltage through the device sensitivity.
When ST is activated, the device output level is given by the algebraic sum of the signals produced by the
acceleration acting on the sensor and by the electrostatic test-force. If the output signals change within
the amplitude specified inside Table 3, than the sensor is working properly and the parameters of the in-
terface chip are within the defined specification.
3.1.4 Output impedance
Describes the resistor inside the output stage of each channel. This resistor is part of a filter consisting of
an external capacitor of at least 320pF and the internal resistor. Due to the high resistor level only small,
inexpensive external capacitors are needed to generate low corner frequencies. When interfacing with an
ADC it is important to use high input impedance input circuitries to avoid measurement errors. Note that
the minimum load capacitance forms a corner frequency beyond the resonance frequency of the sensor.
For a flat frequency response a corner frequency well below the resonance frequency is recommended.
In general the smallest possible bandwidth for an particular application should be chosen to get the best
results.
相關PDF資料 |
PDF描述 |
|---|---|
| LIS2L06AL | MEMS INERTIAL SENSOR: 2-axis - +/- 2g/6g ULTRACOMPACT LINEAR ACCELEROMETER |
| LIS2L06ALTR | MEMS INERTIAL SENSOR: 2-axis - +/- 2g/6g ULTRACOMPACT LINEAR ACCELEROMETER |
| LIS302ALK | MEMS motion sensor 3-axis-【2g analog output "piccolo" accelerometer |
| LIS302ALKTR | MEMS motion sensor 3-axis-【2g analog output "piccolo" accelerometer |
| LIS3L02AS4 | MEMS INERTIAL SENSOR 3-Axis - 【2g/【6g LINEAR ACCELEROMETER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS2L02AS4-TR | 功能描述:加速計 - 板上安裝 LINEAR ACCELEROMETER 2 AXIS 2G/6G RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS2L02AS-TR | 制造商:STMicroelectronics 功能描述:LINEAR ACCELEROMETER 2 AXIS - Tape and Reel |
| LIS2L06A | 制造商:STMicroelectronics 功能描述:ACCELERATION SENSOR IC |
| LIS2L06AL | 功能描述:加速計 - 板上安裝 2-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS2L06AL_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR:2-axis - +/- 2g/6g ultracompact linear accelerometer |
發布緊急采購，3分鐘左右您將得到回復。