- 您現在的位置：買賣IC網 > PDF目錄383255 > LCP1521 (意法半導體) PROGRAMMABLE TRANSIENT VOLTAGE SUPPRESSOR FOR SLIC PROTECTION PDF資料下載
參數資料
| 型號： | LCP1521 |
| 廠商： | 意法半導體 |
| 英文描述： | PROGRAMMABLE TRANSIENT VOLTAGE SUPPRESSOR FOR SLIC PROTECTION |
| 中文描述： | 可編程瞬態電壓抑制器保護的用戶接口 |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 112K |
| 代理商： | LCP1521 |
TECHNICAL INFORMATION
Fig. A1:
LCP1521 concept behavior.
Figure A1 shows the classical protection circuit using the LCP1521 crowbar concept. This topology
has been developed to protect the new high voltage SLIC’s, it allows to program the negative firing
threshold while the positive clamping value is fixed at GND.
When a negative surge occurs on one wire (L1 for example) a current Ign flows through the base of the
transistor T1 and then injects a current in the gate of the thyristor Th1. Th1 fires and all the surge current
flows through the ground. After the surge when the current flowing through Th1 becomes less negative
than the holding current I
H
, then Th1 switches off.
When a positive surge occurs on one wire (L1 for example) the diode D1 conducts and the surge current
flows through the ground.
Fig. A2:
Example of PCB layout based on LCP1521 protection.
In order to minimize the remaining voltage across the SLIC inputs during the surge, the TIP and RING pins
of the LCP1521 are doubled (Pins 1 and 8 for TIP / Pins 4 and 5 for RING).
This fact allows the board designer to connect the track like designed in figure A2. With such a PCB design,
the extra voltages caused by track stray inductance (LdI / dt) remain located on the line side of the LCP and
do not affects its SLIC side.
The capacitor C is used to speed up the crowbar structure firing during the fast surge edges.
This allows to minimize the dynamical breakover voltage at the SLIC Tip and Ring inputs during fast strikes.
Please note that this capacitor is generally present around the SLIC - Vbat pin.
So to be efficient it has be as close as possible from the LCP1521 Gate pin and from the reference ground
track (or plan) (see Fig. A2). The optimized value for C is 220nF.
To the
line side
To the
SLIC side
2
GND
V Ring
GND
Gate
TIP
RING
GND
-Vbat
C
Rs1
Rs2
L 1
L 2
VTip
Th1
D1
T1
IG
ID1
LCP1521
6/9
相關PDF資料 |
PDF描述 |
|---|---|
| LCP152 | Programmable transient voltage suppressor for SLIC protection |
| LCP3121 | OVERVOLTAGE AND OVERCURRENT PROTECTION FOR TELECOM LINE |
| LD1084D2M90 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| LD1084D2T90 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| LD1084V120 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LCP1521RL | 功能描述:ESD 抑制器 Dual Program TVS RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
| LCP1521S | 功能描述:TVS 二極管 - 瞬態電壓抑制器 SLIC Protection IC RoHS:否 制造商:Vishay Semiconductors 極性:Bidirectional 工作電壓: 擊穿電壓:58.9 V 鉗位電壓:77.4 V 峰值浪涌電流:38.8 A 系列: 封裝 / 箱體:DO-214AB 最小工作溫度:- 55 C 最大工作溫度:+ 150 C |
| LCP1521S_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Programmable transient voltage suppressor for SLIC protection |
| LCP1521SRL | 功能描述:ESD 抑制器 SLIC Protection IC RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
| LCP152DEE | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Programmable transient voltage suppressor for SLIC protection |
發布緊急采購，3分鐘左右您將得到回復。