- 您現在的位置：買賣IC網 > PDF目錄98000 > LCP-8500A4EDRH FIBER OPTIC TRANSCEIVER, 840-860nm, 8500Mbps(Tx), 8500Mbps(Rx), SURFACE MOUNT, LC CONNECTOR PDF資料下載
參數資料
| 型號： | LCP-8500A4EDRH |
| 元件分類： | 光收發 |
| 英文描述： | FIBER OPTIC TRANSCEIVER, 840-860nm, 8500Mbps(Tx), 8500Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| 封裝： | ROHS COMPLIANT PACKAGE |
| 文件頁數： | 11/14頁 |
| 文件大?。?/td> | 237K |
| 代理商： | LCP-8500A4EDRH |
DELTA ELECTRONICS, INC.
6
2010/6/4
Rev. S0
www.deltaww.com
Low speed electrical control pins and 2-wire interface
In addition to the 2-wire serial interface, the SFP+ module has the following low speed pins for control and
status:
TX_Fault
TX_Disable
RS0/RS1
MOD_ABS
RX_LOS
1. TX_Fault
.TX_Fault is a module output pin that when High, indicates that the module transmitter has detected a fault
condition related to laser operation or safety.
The TX_Fault output pin is an open drain/collector and must be pulled p to the Host_Vcc with 4.7k-10k
ohms on the host board.
2. TX_Disable
TX_Disable is a module input pin. When TX_Disable is asserted High or Left open, the SFP+ module
transmitter output must be turned off. The TX_DIS pin must be pulled up to VccT in the SFP+ module.
3. RS0/RS1
RS0 and RS1 are module input rate select pins and are pulled low to VeeT with a > 30k
resistor in the
module. RS0 is an input hardware pin which optionally selects the optical receives data path rate
coverage for an SFP+ module. RS1 is an input hardware pin which optionally selects the optical transmits
path data rate coverage for an SFP+ module.
RS1 is commonly connected to VeeT or VeeR in the legacy SFP modules. The host needs to ensure that
it will not be damaged if this pin is connected to VeeT or VeeR in the module.
4. MOD_ABS
Mod_ABS is pulled up to Host_Vcc with 4.7k-10k ohms on the host board and connected to VeeT or VeeR
in the SFP+ module. MOD_ABS is then asserted “High” when the SFP+ module is physically absent from
a host slot. In the SFP MSA (INF8074i) this pin had the same function but is called MOD_DEF0.
5. SCL/SDA
SCL is the 2-wire interface clock and SDA is the 2-wire interface data line. SCL and SDA are pulled up to
a voltage in the range of 3.14V to 3.46V on the host.
6. RX_LOS
RX_LOS when High Indicated an optical signal level below that specified in the relevant standard. The
RX_LOS pin is an open drain/collector outpit and must be pulled up to host Vcc with a 4.7k-10k ohms on
the host board.
RX_LOS assert min and de-assert max are defined in the relevant standard. To avoid spurious transition
of RX_LOS a minimum hysteresis of 0.5 dBo is recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| LCP-8500A4EDR | FIBER OPTIC TRANSCEIVER, 840-860nm, 8500Mbps(Tx), 8500Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-8500B4QDRH | FIBER OPTIC TRANSCEIVER, 1260-1355nm, 8500Mbps(Tx), 8500Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-8500B4QDRT | FIBER OPTIC TRANSCEIVER, 1260-1355nm, 8500Mbps(Tx), 8500Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-8500B4QDR | FIBER OPTIC TRANSCEIVER, 1260-1355nm, 8500Mbps(Tx), 8500Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LIS1R02 | SPECIALTY ANALOG CIRCUIT, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LCP8P-10-10K | 功能描述:精度電位計 0.2W 10Kohms 15% RoHS:否 制造商:Bourns 產品:Precision Potentiometer 安裝風格:Panel 線性: 錐度: 轉數:3 元件類型:Wirewound 軸類型:Slotted 電阻:2 kOhms 端接類型:Solder Lug 電壓額定值: 容差:5 % |
| LCP8P-10-10K | 制造商:ETI Systems 功能描述:Linear Motion Control Series:LCP8 |
| LCP8P-10-1K | 功能描述:精度電位計 0.2W 1Kohms 15% RoHS:否 制造商:Bourns 產品:Precision Potentiometer 安裝風格:Panel 線性: 錐度: 轉數:3 元件類型:Wirewound 軸類型:Slotted 電阻:2 kOhms 端接類型:Solder Lug 電壓額定值: 容差:5 % |
| LCP8P-10-20K | 功能描述:精度電位計 .2W 20K ohms 15% RoHS:否 制造商:Bourns 產品:Precision Potentiometer 安裝風格:Panel 線性: 錐度: 轉數:3 元件類型:Wirewound 軸類型:Slotted 電阻:2 kOhms 端接類型:Solder Lug 電壓額定值: 容差:5 % |
| LCP8P-10-50K | 制造商:ETI Systems 功能描述:Pot,Precision;Cnd Pl;Rest 50 Kilohms;Panel;Linear;Pwr-Rtg 0.2W;Shaft Dia 0.079in |
發布緊急采購，3分鐘左右您將得到回復。