- 您現在的位置：買賣IC網 > PDF目錄97999 > LCP-6144A4EDR FIBER OPTIC TRANSCEIVER, 840-860nm, 6144Mbps(Tx), 6144Mbps(Rx), SURFACE MOUNT, LC CONNECTOR PDF資料下載
參數資料
| 型號： | LCP-6144A4EDR |
| 元件分類： | 光收發 |
| 英文描述： | FIBER OPTIC TRANSCEIVER, 840-860nm, 6144Mbps(Tx), 6144Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| 封裝： | ROHS COMPLIANT PACKAGE |
| 文件頁數： | 13/15頁 |
| 文件大?。?/td> | 260K |
| 代理商： | LCP-6144A4EDR |
LCP-6144A4EDRx
DELTA ELECTRONICS, INC.
7
Revision: S0
2010/09/08
www.deltaww.com
Low speed electrical control pins and 2-wire interface
In addition to the 2-wire serial interface, the SFP+ module has the following low speed pins for control and
status:
TX_Fault
TX_Disable
RS0/RS1
MOD_ABS
RX_LOS
1 TX_Fault
TX_Fault is a module output pin that when High, indicates that the module transmitter has detected a fault
condition related to laser operation or safety.
The TX_Fault output pin is an open drain/collector and must be pulled p to the Host_Vcc with 4.7k-10k
ohms on the host board
2 TX_Disable
TX_Disable is a module input pin. When TX_Disable is asserted High or Left open, the SFP+ module
transmitter output must be turned off. The TX_DIS pin must be pulled up to VccT in the SFP+ module..
3 RS0/RS1
RS0 and RS1 are module input rate select pins and are pulled low to VeeT with a > 30k
resistor in the
module. RS0 is an input hardware pin which optionally selects the optical receive data path rate coverage
for an SFP+ module. RS1 is an input hardware pin which optionally selects the optical transmit path data
rate coverage for an SFP+ module. RS1 is commonly connected to VeeT or VeeR in the legacy SFP
modules. The host needs to ensure that it will not be damaged if this pin is connected to VeeT or VeeR in
the module.
4 MOD_ABS
Mod_ABS is pulled up to Host_Vcc with 4.7k-10k ohms on the host board and connected to VeeT or VeeR
in the SFP+ module. MOD_ABS is then asserted “High” when the SFP+ module is physically absent from
a host slot. In the SFP MSA (INF8074i) this pin had the same function but is called MOD_DEF0.
5 SCL/SDA
SCL is the 2-wire interface clock and SDA is the 2-wire interface data line. SCL and SDA are pulled up to
a voltage in the range of 3.14V to 3.46V on the host.
6 RX_LOS
RX_LOS when High indicated an optical signal level below that specified in the relevant standard. The
RX_LOS pin is an open drain/collector output and must be pulled up to host Vcc with a 4.7k-10k ohms on
the host board.
RX_LOS assert min and de-assert max are defined in the relevant standard. To avoid spurious transition
of RX_LOS a minimum hysteresis of 0.5 dB is recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| LCP-6144A4EDRH | FIBER OPTIC TRANSCEIVER, 840-860nm, 6144Mbps(Tx), 6144Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-6144B4HDRT | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 6144Mbps(Tx), 6144Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-6144B4HDR | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 6144Mbps(Tx), 6144Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-6144B4HDRH | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 6144Mbps(Tx), 6144Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-6144B4MDR | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 6144Mbps(Tx), 6144Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LCP-624-G | 制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 24 POS 2.54MM SLDR ST TH - Bulk |
| LCP-640-T | 制造商:Samtec Inc 功能描述:ADAPTER 40 POS TIN LOW COST - Bulk |
| LCP-64GB-S250 | 制造商:Renesas Electronics Corporation 功能描述:LOW COST PROBE, 64 PIN, SHIELD 制造商:Renesas Electronics Corporation 功能描述:LOW COST PROBE, 64 PIN, SHIELD - Bulk 制造商:Renesas Electronics Corporation 功能描述:EMULATION PROBE 250MM SHLD CABLE |
| LCP6KE6.8 | 制造商:FRONTIER 制造商全稱:Frontier Electronics. 功能描述:LOW CAPACITANCE 600W TRANSIENT VOLTAGE SUPPRESSORS |
| LCP8-2539-5K | 功能描述:精度電位計 POT RECTANGULAR 5K RoHS:否 制造商:Bourns 產品:Precision Potentiometer 安裝風格:Panel 線性: 錐度: 轉數:3 元件類型:Wirewound 軸類型:Slotted 電阻:2 kOhms 端接類型:Solder Lug 電壓額定值: 容差:5 % |
發布緊急采購，3分鐘左右您將得到回復。