- 您現在的位置：買賣IC網 > PDF目錄97999 > LCP-2488D4R53R FIBER OPTIC TRANSCEIVER, 155Mbps(Tx), 155Mbps(Rx), SURFACE MOUNT, LC CONNECTOR PDF資料下載
參數資料
| 型號： | LCP-2488D4R53R |
| 元件分類： | 光收發 |
| 英文描述： | FIBER OPTIC TRANSCEIVER, 155Mbps(Tx), 155Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| 封裝： | ROHS COMPLIANT PACKAGE |
| 文件頁數： | 13/15頁 |
| 文件大?。?/td> | 1493K |
| 代理商： | LCP-2488D4R53R |
LCP-2488D4RXXR
Series
DELTA ELECTRONICS, INC.
7
Revision: S3
05/18/2010
www.deltaww.com
1)
TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K
resistor on the
host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of
some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.
2)
TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the
module with a 4.7 – 10 K
resistor. Its states are:
Low (0 – 0.8V):
Transmitter on
(>0.8, < 2.0V):
Undefined
High (2.0 – 3.465V):
Transmitter Disabled
Open:
Transmitter Disabled
3)
Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10K resistor
on the host board. The pull-up voltage shall be VccT or VccR (see Section IV for further details). Mod-Def
0 is grounded by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire
serial interface for serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID
4)
LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10K
resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received
optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low
indicates normal operation. In the low state, the output will be pulled to < 0.8V.
5)
VeeR and VeeT may be internally connected within the SFP module.
6)
RD-/+: These are the differential receiver outputs. They are AC coupled 100
differential lines which
should be terminated with 100
(differential) at the user SERDES. The AC coupling is done inside the
module and is thus not required on the host board. The voltage swing on these lines will be between 370
and 2000 mV differential (185 – 1000 mV single ended) when properly terminated.
7)
VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the
SFP connector pin. Recommended host board power supply filtering is shown below. Inductors with DC
resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP input
pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the
SFP transceiver module will result in an inrush current of no more than 30mA greater than the steady
state value. VccR and VccT may be internally connected within the SFP transceiver module.
8)
TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100
differential termination inside the module. The AC coupling is done inside the module and is thus not
required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200 mV
single-ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600
mV single-ended) be used for best EMI performance.
相關PDF資料 |
PDF描述 |
|---|---|
| LCP-3072B4LDRH | FIBER OPTIC TRANSCEIVER, 1285-1345nm, 3072Mbps(Tx), 3072Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-3072B4LDRT | FIBER OPTIC TRANSCEIVER, 1285-1345nm, 3072Mbps(Tx), 3072Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-3072B4LDR | FIBER OPTIC TRANSCEIVER, 1285-1345nm, 3072Mbps(Tx), 3072Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-4250A4CDR | FIBER OPTIC TRANSCEIVER, 830-860nm, 4250Mbps(Tx), 4250Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-4250A4CDRT | FIBER OPTIC TRANSCEIVER, 830-860nm, 4250Mbps(Tx), 4250Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LCP-28CT-250 | 制造商:Renesas Electronics Corporation 功能描述:LOW COST PROBE, 250MM - Bulk 制造商:Renesas Electronics Corporation 功能描述:EMULATION PROBE 250MM CABLE |
| LCP-28GT-250 | 制造商:Renesas Electronics Corporation 功能描述:LOW COST PROBE, 250MM - Bulk 制造商:Renesas Electronics Corporation 功能描述:EMULATION PROBE 250MM CABLE |
| LCP3-0.36-680 | 制造商:TALEMA 制造商全稱:TALEMA 功能描述:Miniature Low Cost Toroidal Inductors |
| LCP3-0.42-470 | 制造商:TALEMA 制造商全稱:TALEMA 功能描述:Miniature Low Cost Toroidal Inductors |
| LCP3-0.50-330 | 制造商:TALEMA 制造商全稱:TALEMA 功能描述:Miniature Low Cost Toroidal Inductors |
發布緊急采購，3分鐘左右您將得到回復。