- 您現在的位置：買賣IC網 > PDF目錄97999 > LCP-2488B4JDRT FIBER OPTIC TRANSCEIVER, 1260-1360nm, 2488Mbps(Tx), 2488Mbps(Rx), SURFACE MOUNT, LC CONNECTOR PDF資料下載
參數資料
| 型號： | LCP-2488B4JDRT |
| 元件分類： | 光收發 |
| 英文描述： | FIBER OPTIC TRANSCEIVER, 1260-1360nm, 2488Mbps(Tx), 2488Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| 封裝： | ROHS COMPLIANT PACKAGE |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 262K |
| 代理商： | LCP-2488B4JDRT |
DELTA ELECTRONICS, INC.
5
2008/11/17
Rev. 0A
www.deltaww.com
Notes:
1)
TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor on the host
board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of some kind.
Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.
2)
TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module
with a 4.7 – 10 K resistor. Its states are:
Low (0 – 0.8V):
Transmitter on
(>0.8, < 2.0V):
Undefined
High (2.0 – 3.465V):
Transmitter Disabled
Open:
Transmitter Disabled
3)
Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10Kresistor on the
host board. The pull-up voltage shall be VccT or VccR (see Section IV for further details). Mod-Def 0 is grounded
by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial interface for
serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID
4)
LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor.
Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is
below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In
the low state, the output will be pulled to < 0.8V.
5)
VeeR and VeeT may be internally connected within the SFP module.
6)
RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be
terminated with 100 (differential) at the user SERDES. The AC coupling is done inside the module and is thus
not required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential
(185 – 1000 mV single ended) when properly terminated.
7)
VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP
connector pin. Recommended host board power supply filtering is shown below. Inductors with DC resistance of
less than 1 ohm should be used in order to maintain the required voltage at the SFP input pin with 3.3V supply
voltage. When the recommended supply-filtering network is used, hot plugging of the SFP transceiver module will
result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be
internally connected within the SFP transceiver module.
8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100
differential termination inside the module. The AC coupling is done inside the module and is thus not
required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200
mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 –
600 mV single-ended) be used for best EMI performance.
相關PDF資料 |
PDF描述 |
|---|---|
| LCP-2488D4R49R | FIBER OPTIC TRANSCEIVER, 155Mbps(Tx), 155Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-2488D4R51R | FIBER OPTIC TRANSCEIVER, 155Mbps(Tx), 155Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-2488D4R55R | FIBER OPTIC TRANSCEIVER, 155Mbps(Tx), 155Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-2488D4R57R | FIBER OPTIC TRANSCEIVER, 155Mbps(Tx), 155Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| LCP-2488D4R59R | FIBER OPTIC TRANSCEIVER, 155Mbps(Tx), 155Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LCP-28CT-250 | 制造商:Renesas Electronics Corporation 功能描述:LOW COST PROBE, 250MM - Bulk 制造商:Renesas Electronics Corporation 功能描述:EMULATION PROBE 250MM CABLE |
| LCP-28GT-250 | 制造商:Renesas Electronics Corporation 功能描述:LOW COST PROBE, 250MM - Bulk 制造商:Renesas Electronics Corporation 功能描述:EMULATION PROBE 250MM CABLE |
| LCP3-0.36-680 | 制造商:TALEMA 制造商全稱:TALEMA 功能描述:Miniature Low Cost Toroidal Inductors |
| LCP3-0.42-470 | 制造商:TALEMA 制造商全稱:TALEMA 功能描述:Miniature Low Cost Toroidal Inductors |
| LCP3-0.50-330 | 制造商:TALEMA 制造商全稱:TALEMA 功能描述:Miniature Low Cost Toroidal Inductors |
發布緊急采購，3分鐘左右您將得到回復。