- 您現在的位置：買賣IC網 > PDF目錄30737 > LC895195 SPECIALTY CONSUMER CIRCUIT, PQFP144 PDF資料下載
參數資料
| 型號： | LC895195 |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP144 |
| 封裝： | SQFP-144 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 63K |
| 代理商： | LC895195 |
No. 5192-7/8
LC895195
ZSWAIT (output)
When the microcontroller is accessing RAM, the sub-CPU must wait if this pin is low.
D7 to D0 (I/O)
Microcontroller data bus. Pull-up resistors are built in.
ZINT (output)
Interrupt request signal output to the microcontroller. A pull-up resistor is built in.
ZINT1 (output)
Interrupt request signal output from the IDE block to the microcontroller. An external pull-up resistor must be
connected to this pin.
3. Buffer RAM Pins
IO0 to IO15 (I/O)
Buffer DRAM data bus. A pull-up resistor is built in.
RA0 to RA9 (output)
Buffer RAM address lines.
ZRAS0, ZRAS1 (output)
Buffer DRAM RAS outputs. Normally, ZRAS0 is used, but if two 1-Mb (64k
× 16 bits) chips are used, then both
ZRAS0 and ZRAS1 are used, one for each of the chips.
ZCAS0, ZCAS1 (output)
Buffer DRAM CAS outputs. Normally, ZCAS0 is used, but if two 1-Mb (64k
× 16 bits) chips are used, then both
ZCAS0 and ZCAS1 are used, one for each of the chips. When using a two-CAS type DRAM, connect ZCAS0 to
UCAS, and ZCAS1 to LCAS.
ZOE (output)
Buffer DRAM read output signal.
ZUWE, ZLWE (output)
Buffer DRAM write output signals. Connected the corresponding DRAM pins.
4. Subcode Interface Pins
EXCK, WFCK, SBSO, SCOR (input or output)
These are the subcode interface connections. The LC895195 acquires subcode data by connection with the CD-
DSP and sends that data to the host.
5. CD-DSP Data Pins
BCK, SDATA, LRCK, C2PO (input)
The LC895195 reads in the CD-ROM data by connecting to the CD-DSP.
The C2PO pin is used for the C2 flags.
6. Other Pins
ZRESET (input)
This is the LC895195 reset pin. The LC895195 is reset by a low level on this pin.
This pin must be held low for at least 1 s when power is first applied.
XTALCK, XTAL
These pins can drive a 16.9344-MHz or 33.8688-MHz oscillator.
Alternatively, an external clock can be input to the XTALCK pin.
MCK (output)
This pin outputs either the XTALCK frequency or that frequency divided by 2. This output can be turned off.
MCK2 (output)
This pin outputs either the XTALCK frequency or that frequency divided by 512. This output can be turned off.
ZRSTIC (output)
This pin can be set to output a low level either by writing to the microcontroller write register R46 bit 7
(ZSYSRTS) or by setting the ZHRST pin (pin 103) low. This pin goes to the high-impedance state when both
ZSYSRST and ZHRST are high.
Since this pin has an open-drain circuit, an external pull-up resistor must be used.
相關PDF資料 |
PDF描述 |
|---|---|
| LC895196K | SPECIALTY CONSUMER CIRCUIT, PQFP144 |
| LC895196 | SPECIALTY CONSUMER CIRCUIT, PQFP144 |
| LC895198 | SPECIALTY CONSUMER CIRCUIT, PQFP120 |
| LC895199K | SPECIALTY CONSUMER CIRCUIT, PQFP144 |
| LC895297 | SPECIALTY CONSUMER CIRCUIT, PQFP176 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC895196 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:ATA-PI Compatible CD-ROM Decoder IC |
| LC895196K | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:ATA-PI Compatible CD-ROM Decoder IC |
| LC895198 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CD-ROM Decoder for 32 x ATAPI (IDE) Drives |
| LC895199K | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:32 CD-ROM Decoder with ATAPI (IDE) Interface |
| LC895297 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Full CAV 20 x CD-ROM Decoder with Built-in ATA-PI (IDE) Interface and CD-DSP |
發布緊急采購，3分鐘左右您將得到回復。