- 您現在的位置：買賣IC網 > PDF目錄30737 > LC8904Q SPECIALTY CONSUMER CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | LC8904Q |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | QFP-48 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 321K |
| 代理商： | LC8904Q |
Analog Source Mode
The LC8904Q enters analog source mode in the following two cases:
1. Analog source mode is selected from the microprocessor interface.
2. If the input pin specified for data demodulation goes to the no signal state.
In this mode, the clock that operates the whole system is taken from the crystal oscillator clock, and the PLL and data
demodulation circuits are stopped. The BCLK, LRCK, CLKOUT1, and CLKOUT2 clocks are output.
The output pins have the following functions in analog source mode:
1. DOUT/V
Data output as specified by the microprocessor interface
2. ERROR
Outputs the error state, i.e. a high level.
3. SUB1 and SUB2
These pins output the “#1” lock error state.
4. DATAOUT
Outputs the lock error state, i.e., a low level.
5. EMPHA
Outputs the lock error state, i.e., a low level.
6. Microprocessor interface codes
Input codes: The codes loaded from the microprocessor interface are retained.
Output codes: The same codes as output for a PLL lock error.
Crystal Oscillator
1. A built-in detector circuit determines whether or not a data input signal is present. This circuit operates from either
the VCO or the crystal oscillator clock. When the power supply is coming up, this clock is supplied from the VCO,
and if a no-data state is detected, the system switches to the crystal oscillator clock. Here, if the clock is not supplied
from the crystal oscillator after a no-data state is detected, the whole system goes to the stopped state, and, since the
detector circuit does not operate even if data is supplied, the system will remain in the stopped state.
2. The XIN and XOUT pins include a built-in oscillator amplifier circuit, and operate as follows when a crystal
oscillator element is attached.
Note: * When data is present, the XIN pin is pulled up internally.
Data Output Timing
1. Data is output in synchronization with the falling edge of the BCLK signal.
2. Data, BCLK, and LRCK are output in synchronization with the rising edge of the 256fs clock.
3. The figure on the following page shows the data output timing.
No. 5014-17/20
LC8904Q
Pin
Data present*
No data
XIN
H
Crystal oscillator input accepted
XOUT
L
Outputs the inverse of the XIN pin state.
相關PDF資料 |
PDF描述 |
|---|---|
| LC89051V | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC89052TA-E | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC890561W | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC890561W | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC89057W-VF4-E | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC89051V | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Digital Audio Interface Receiver |
| LC89052T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Digital Audio Interface Receiver |
| LC89052TA-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| LC89052TA-TLM-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| LC89052THS-E | 制造商:ON Semiconductor 功能描述:AUDIO I/F RECEIVER |
發布緊急采購，3分鐘左右您將得到回復。