- 您現在的位置：買賣IC網 > PDF目錄358765 > LC78211 (Sanyo Electric Co.,Ltd.) Analog Function Switch PDF資料下載
參數資料
| 型號： | LC78211 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Analog Function Switch |
| 中文描述： | 模擬功能開關 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 115K |
| 代理商： | LC78211 |
Pin Functions
Operation
1. Data Input Procedure
The LC78211, LC78212 and LC78213 are controlled by inputting specified data to the CL, DI and CE pins. The
input data consists of 12 bits, of which four bits are address and eight bits are data.
Bits correspond to the L1 to L8 and R1 to R8 analog switches, and a value of one turns the corresponding switch on,
and a value of zero turns it off.
0.........Off
1.........On
The address is used when the chip is connected to a shared bus. The data (address) that must be transmitted depends
on the S pin and the particular product as shown in the table below.
Note: The bit for switch eight in the LC78213 is a “don’t care” bit, that is it can be either 0 or 1 without affecting
chip function. This is because the LC78213 has two sets of seven (not eight) circuits.
No. 4817-5/6
LC78211, 78212, 78213
Pin
I/O
Internal equivalent circuit
Pin function
V
DD
, V
SS
, V
EE
L1 to L8, R1 to R8,
LCOM1 to LCOM4,
RCOM1 to RCOM4
CL, DI, CE
S
RES
I
I
I
See the block diagram.
Power supply
Analog switch input and output
Serial data input (Schmitt buffer)
CL..............Clock input
DI...............Data input
CE .............Chip enable
Selection of one of two chips
The address is set to the values shown in the table below according to
the level input to the S pin.
Reset input
The states of the analog switches are undefined when power is first
applied. Setting this pin low will force all switches the off state.
Product
S pin
level
Address
A
0
0
A
1
1
A
2
0
A
3
1
LC78211
L
H
1
1
0
1
LC78212
L
0
0
1
1
H
1
0
1
1
LC78213
L
0
1
1
1
H
1
1
1
1
Product
S pin
level
Address
A
0
0
A
1
1
A
2
0
A
3
1
LC78211
L
H
1
1
0
1
LC78212
L
0
0
1
1
H
1
0
1
1
LC78213
L
0
1
1
1
H
1
1
1
1
相關PDF資料 |
PDF描述 |
|---|---|
| LC7821N | ANALOG FUNTION SWITCH |
| LC7821 | Analog Function Switch |
| LC7824 | Analog Function Switch |
| LC7851E | QPSK Demodulation and Audio Signal-Processing IC for Satellite Broadcast Reception |
| LC7851 | QPSK Demodulation and Audio Signal-Processing IC for Satellite Broadcast Reception |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC78211-E | 制造商:ON Semiconductor 功能描述:ANALOG FUNCTION SWITCH - Ammo Pack 制造商:ON Semiconductor 功能描述:FNFLD / ANALOG FUNCTION SWITCH |
| LC78212 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Analog Function Switch |
| LC78212-E | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| LC78213 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Analog Function Switch |
| LC78213-E | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。