- 您現在的位置：買賣IC網 > PDF目錄358765 > LC75893M (Sanyo Electric Co.,Ltd.) 1/3 Duty LCD Display Driver with Key Input Function PDF資料下載
參數資料
| 型號： | LC75893M |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | 1/3 Duty LCD Display Driver with Key Input Function |
| 中文描述： | 1 / 3職務液晶顯示驅動器與關鍵輸入功能 |
| 文件頁數： | 15/23頁 |
| 文件大?。?/td> | 389K |
| 代理商： | LC75893M |
Voltage Detection Type Reset Circuit (VDET)
This circuit generates an output signal and resets the system when power is first applied and when the voltage drops, i.e.,
when the power supply voltage is less than or equal to the power down detection voltage VDET, which is 3.0 V, typical.
To assure that this function operates reliably, a capacitor must be added to the power supply line so that the power supply
voltage V
DD
rise time when power is first applied and the power supply voltage V
DD
fall time when the voltage drops are
both at least 1 ms. (See Figure 3.)
System Reset
The LC75893M supports the reset method described below. When a system reset is applied, display is turned off, key
scanning is stopped, and all the key data is reset to low. When the reset is cleared, display is turned on and key scanning
become possible.
1. Reset method
If at least 1 ms is assured as the supply voltage V
DD
rise time when power is applied, a system reset will be applied by
the VDET output signal when the supply voltage is brought up. If at least 1 ms is assured as the supply voltage V
DD
fall time when power drops, a system reset will be applied in the same manner by the VDET output signal when the
supply voltage is lowered. Note that the reset is cleared at the point when all the serial data (the display data D1 to
D48 and the control data) has been transferred, i.e., on the fall of the CE signal on the transfer of the last direction
data, after all the direction data has been transferred. (See Figure 3.)
2. LC75893M internal block states during the reset period
CLOCK GENERATOR
Reset is applied and the base clock is stopped. However the OSC pin state (normal or sleep mode) is determined
after the S0 and S1 control data bits are transferred.
COMMON DRIVER, SEGMENT DRIVER & LATCH
Reset is applied and the display is turned off. However, display data can be input to the latch circuit in this state.
KEY SCAN
Reset is applied, the circuit is set to the initial state, and at the same time the key scan operation is disabled.
KEY BUFFER
Reset is applied and all the key data is set to low.
CCB INTERFACE, CONTROL REGISTER, SHIFT REGISTER
Since serial data transfer is possible, these circuits are not reset.
Figure 3
No. 5971-15/23
LC75893M
相關PDF資料 |
PDF描述 |
|---|---|
| LC7730M | Stable Long-running Timer(穩定的運行時間長的定時器) |
| LC78010E | Video CD and CD-G Digital RGB Encoder LSI |
| LC78011E | Digital RGB Encoder IC for Video CD and CD-G |
| LC7802 | Output Port Expansion IC for VTR Applications |
| LC7815 | 2-Pole 4-Position Analog Function Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC75893M-TLM-E | 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LC75897PW | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/3, 1/4-Duty General-Purpose LCD Display Driver |
| LC75897PW-E | 功能描述:LCD 驅動器 LCD DISPLAY DRIVER RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| LC75897PWS-T-E | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays 制造商:ON Semiconductor 功能描述:ON Semiconductor LC75897PWS-T-E Interface Misc 制造商:ON Semiconductor 功能描述:FTRAY / LCD DISPLAY DRIVER |
| LC75A | 制造商:Microsemi Corporation 功能描述:TVS SGL UNI-DIR 75V 1.5KW 2PIN DO-13 - Bulk 制造商:Microsemi Corporation 功能描述:TVS DIODE 75VWM 121VC DO202AA |
發布緊急采購，3分鐘左右您將得到回復。