- 您現在的位置：買賣IC網 > PDF目錄358765 > LC75853NE (Sanyo Electric Co.,Ltd.) 1/3 Duty General-Purpose LCD Display Driver(1/3占空通用LCD顯示驅動器) PDF資料下載
參數資料
| 型號： | LC75853NE |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | 1/3 Duty General-Purpose LCD Display Driver(1/3占空通用LCD顯示驅動器) |
| 中文描述： | 1 / 3職務通用液晶顯示驅動程序（1 / 3占空通用液晶顯示驅動器） |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 418K |
| 代理商： | LC75853NE |
Voltage Detection Type Reset Circuit (VDET)
This circuit generates an output signal and resets the system when power is first applied and when the voltage drops, i.e.,
when the power supply voltage is less than or equal to the power down detection voltage VDET, which is 3.0 V, typical.
To assure that this function operates reliably, a capacitor must be added to the power supply line so that the power
supply voltage V
DD
rise time when power is first applied and the power supply voltage V
DD
fall time when the voltage
drops are both at least 1 ms. (See Figure 3.)
System Reset
1. Reset method
If at least 1 ms is assured as the supply voltage V
DD
rise time when power is applied, a system reset will be applied
by the VDET output signal when the supply voltage is brought up. If at least 1 ms is assured as the supply voltage
V
DD
fall time when power drops, a system reset will be applied in the same manner by the VDET output signal when
the supply voltage is lowered. Note that the reset is cleared at the point when all the serial data (the display data D1
to D126 and the control data) has been transferred, i.e., on the fall of the CE signal on the transfer of the last
direction data, after all the direction data has been transferred. (See Figure 3.)
Figure 3
2. LC75853NE/NW internal block states during the reset period
CLOCK GENERATOR
Reset is applied and the base clock is stopped. However the OSC pin state (normal or sleep mode) is determined
after the S0 and S1 control data bits are transferred.
COMMON DRIVER, SEGMENT DRIVER & LATCH
Reset is applied and the display is turned off. However, display data can be input to the latch circuit in this state.
KEY SCAN
Reset is applied, the circuit is set to the initial state, and at the same time the key scan operation is disabled.
KEY BUFFER
Reset is applied and all the key data is set to low.
CCB INTERFACE, CONTROL REGISTER, SHIFT REGISTER
Since serial data transfer is possible, these circuits are not reset.
No. 4967-16/24
LC75853NE, 75853NW
Undefined
Defined
Display and control data transfer
Internal data
System reset period
Power supply voltage V
DD
rise time: t1
≥
1 ms
Power supply voltage V
DD
fall time: t2
≥
1 ms
相關PDF資料 |
PDF描述 |
|---|---|
| LC75854E | 1/4 Duty LCD Display Driver with Key Input Function(1/4占空具有鍵輸入功能LCD顯示驅動器) |
| LC75864E | 1/4 Duty LCD Display Drivers with Key Input Function |
| LC75873NE | 1/3 Duty General Purpose LCD Display Driver(1/3占空普通用途LCD顯示驅動器) |
| LC75874E | 1/4-Duty General-Purpose LCD Display Driver(1/4占空通用LCD顯示驅動器) |
| LC75878W | 1/8 to 1/10 Duty General-Purpose LCD Display Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC75853NE-E | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| LC75853NEHS-E | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays |
| LC75853NW | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/3 Duty LCD Display Drivers with Key Input Function |
| LC75853NW-E | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| LC75853NWHS-E | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays |
發布緊急采購，3分鐘左右您將得到回復。