參數資料
型號： LC5822
廠商： Sanyo Electric Co.,Ltd.
英文描述： 4-Bit Single-Chip Microcontrollers Featuring 4 KB to 8 KB of ROM, 1 Kbit of RAM, and an LCD Driver for Medium Speed Small-Scale Control Applications
中文描述： 4位單片微控制器具有4 KB到8的ROM，1千位的RAM，以及為中速小規?？刂浦械膽?yīng)用LCD驅動KB
文件頁數： 7/24頁
文件大?。?/td> 281K
代理商： LC5822
No. 5944-7/24
LC5824, LC5823, LC5822
Continued from preceding page.
Pin No.
Pin
I/O
Function
Options
Status at reset
32
33
34
35
SO1
SO2
SO3
SO4
I/O
I/O port
Input pins used to acquire input data to RAM.
Output pins used to output RAM data.
Pull-down resistors are built in.
SO1 to SO3 are also used as the serial interface pins.
The serial interface function can be selected under program
control.
Pin functions:
SO1: Serial input
SO2: Serial output
SO3: Serial clock
The serial clock can be taken from either internal or external
sources, and can be set up to detect either rising or falling
edges under program control.
Identical to M1 through
M4
Identical to M1 through
M4
31
ALM
Output
Output-only pin
A signal modulated by 0, 3, or 4 can be output under
program control.
Low-level output
40
RES
Input
IC internal reset input
The program counter is set to point to location 00H.
The reset input level can be set to be either high or low.
Either a pull-up or a pull-down resistor is built in.
Note: Applications must apply the reset signal level for at least
500 μs to effect a reset.
Selection of a pull-up or
pull-down resistor
Selection of active-low
or active-high reset
logic
44
64
1
21
Seg 22
Seg 21
Seg 22
Seg 42
Output
LCD panel drive outputs/general-purpose outputs
LCD panel drive
(1) Static
(2) 1/2 bias 1/2 duty
(3) 1/2 bias 1/3 duty
(4) 1/2 bias 1/4 duty
(5) 1/3 bias 1/3 duty
(6) 1/3 bias 1/4 duty
One of items (1) through (5) is selected as a mask option.
General-purpose output ports
(1) CMOS output
(2) p-channel open-drain output
(3) n-channel open-drain output
One of items (1) through (3) is selected as a mask option.
The adoption of the segment PLA in these microcontrollers
means that there is no need for programs to control the
LCD/general-purpose output states of these pins.
Output latch control is supported in the oscillator stopped
standby states and during a reset.
Any combination of LCD and general-purpose output functions
may be used.
Switching between LCD
drive output and
general-purpose output
Switching between the
LCD drive type options
—Static
—1/2 bias
—1/2 bias
—1/2 bias
—1/3 bias
—1/3 bias
General-purpose output
type switching
—CMOS
—p-channel open-drain
—n-channel open-drain
Standby mode output
latch control
1/2 duty
1/3 duty
1/4 duty
1/3 duty
1/4 duty
When used for LCD
drive:
—All lit
—All off
*
Determined by the
master options
When used as general-
purpose outputs:
—High level
—Low level
*
Determined by the
master options
Note: When a
combination of LCD drive
and general-purpose
outputs is selected, these
pins will be either:
All lit/high-level output, or
All off/low-level output.
During the reset period,
the LCD drive functions
as static drive.
65
66
79
80
COM1
COM2
COM3
COM4
Output
Common drive outputs for the LCD panel
The table below lists which pins are used in each of the drive
types.
However, note that the listed alternation frequencies are the
typical specifications when 0 is 32.768 kHz.
41
TST
Input
Test input
In the QIP-80 version, this pin must be connected to V
SS
.
In the chip version, this pin must be left open or connected to
V
SS
.
—
—
TEST
TEST
—
—
Test pins.
(These are not used in the device user interface.)
Note: Note that the “
” symbol indicates that the corresponding
common pin cannot be used in that drive type.
*
In products with the CF
specifications, the
alternation frequency
signal stops briefly.
Static
1/2 duty
1/3 duty
1/4/duty
COM1
G
G
G
G
G
G
G
G
COM2
G
G
G
G
G
G
COM3
G
G
G
G
COM4
G
G
Alternation
frequency
32 Hz
32 Hz
42.7 Hz
64 Hz
相關PDF資料
PDF描述
LC5851N 4-bit Single Chip Microcontroller with LCD Driver(4位微控制器（帶LCD驅動器）)
LC5852N Four-Bit Single-Chip Microcontroller with On-Chip LCD Drivers for Small-Scale Control in Medium-Speed Applications(應用于中等速率中小規模控制的4位微控制器（帶片上LCD驅動器）)
LC5863H 4-BIT SINGLE CHIP MICROCOMPUTER
LC587008 Single-Chip 4-Bit Microprocessors with LCD Driver,2 Kb RAM, and 16 KB ROM on chip(4位單片微控制器（帶LCD驅動器，16K位ROM和2K位RAM）)
LC587202A Single-Chip 4-Bit Micontroller with LCD Driver,512 ×4bit RAM,2K× 16 Bit ROM on chip(單片4位微控制器（帶LCD驅動器，512 ×4位RAM和2K× 16位ROM）)
相關代理商/技術參數
參數描述
LC5823 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontrollers Featuring 4 KB to 8 KB of ROM, 1 Kbit of RAM, and an LCD Driver for Medium Speed Small-Scale Control Applications
LC5824 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontrollers Featuring 4 KB to 8 KB of ROM, 1 Kbit of RAM, and an LCD Driver for Medium Speed Small-Scale Control Applications
LC5824-1K35 制造商:ON Semiconductor 功能描述:
LC5850 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
LC5851 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Small-Scale Control, Medium Speed Type, On-Chip LCD Driver 4-Bit Single Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*