- 您現在的位置：買賣IC網 > PDF目錄358750 > LB8649FN (Sanyo Electric Co.,Ltd.) Monolithic Digital IC Motor Driver for DSCs PDF資料下載
參數資料
| 型號： | LB8649FN |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Monolithic Digital IC Motor Driver for DSCs |
| 中文描述： | 單片數字集成電路的DSC的電機驅動器 |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 239K |
| 代理商： | LB8649FN |
LB8649FN
No.7893-5/9
3. VCM constant current control for SH/AE, or stepping motor drive.
Input
Output
IN9
IN10
IN11
IN12
INHD
OUT9
OUT10
OUT11
OUT12
Vref
ISH
Mode
L
L
L
L
-
-
-
-
-
-
Stand-by
H
L
*
*
H
L
L
H
*
*
L
H
*
*
H
L
H
L
*
*
L
H
L
L
H
1.0V
SH & AE
H
L
*
*
H
L
L
H
*
*
L
H
*
*
H
L
H
L
*
*
L
H
L
H
Setting
voltage
state
Hold
L
L
L
L
H
-
-
-
-
0.67V
Discharge
Stand-by
( - ) is output OFF, and (
*
) is “Don’t care”.
OUT9 and OUT10 are used for the SH.
Quick charge and quick discharge circuitry allows the stabilization of start-up characteristic.
OUT10 and OUT11 are used for the AF.
At the time of stand-by, ISH pin voltage becomes discharge state by the internal transistor and it is set to 0V.
In addition, when IN1 to 8 are input, ISH pin is in discharge state (for start-up correction).
When INHD = “L”, Vref voltage is 1.0V. When INHD = “H”, Vref voltage is 0.67V.
Application Design Notes
1. Constant current setting (ISH, IAE, RFG1, 2, OUT9 to 12)
The constant current setting between pins OUT9 and OUT10 is determined from the ISH input voltage and the
connecting resistor of RFG1. As shown in the block diagram, it is controlled in such a way so that the voltage
generated at the resistor used for current detection connected between RFG1 and GND would be equal to the ISH
input voltage. The formula for calculating the output current is as given below.
(OUT9 to OUT10 Output Current) = (ISH Input Voltage)
÷
(RFG1 Resistor + 0.05
)
The 0.05
here is for a common impedance of the output Tr emitter which drives constant current in the RFG pin
and the sensing wiring for the constant current control amplifier.
In the same way, the constant current setting between pins OUT11 and OUT12 is determined from the IAE input
voltage and the connecting resistor of RFG2.
Furthermore, as the constant current control block within the IC is connected to PGND, when supplying voltage to
the ISH pin or IAE pin which has been divided by resistors be sure to connect the ground side of these resistors to
PGND.
2. Quick charge/discharge circuitry (FC1, OUT9, OUT10)
Quick discharge circuitry has been built in to the shutter control block (OUT9 to OUT10) to support high-speed
shutter control, quick recharge, quick discharge and consecutive shots.
Quick recharge and quick discharge circuitry has not been built in to the AE control block (OUT11 to OUT12).
Therefore, make sure to use the block (OUT9 to OUT10) for the shutter drive.
相關PDF資料 |
PDF描述 |
|---|---|
| LB8649W | Monolithic Digital IC Digital Camera Motor Driver |
| LB8652T | Monolithic Digital IC Driver for Digital Still Cameras |
| LB8655T | Monolithic Digital IC Driver for Digital Still Cameras |
| LB8658FN | Monolithic Digital IC DSC Motor Driver |
| LB8681CL | Monolithic Digital IC Constant Current Driver IC with H-bridge 】 1.5 Channel |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB8649FN_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Motor Driver for DSCs |
| LB8649FNL-TLM-E | 制造商:ON Semiconductor 功能描述: |
| LB8649W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC Digital Camera Motor Driver |
| LB8649W-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 DSC MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB8649W-TBM-E | 功能描述:馬達/運動/點火控制器和驅動器 SYSTEM MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。