- 您現在的位置：買賣IC網 > PDF目錄97997 > LB1927 BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDIP28 PDF資料下載
參數資料
| 型號： | LB1927 |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDIP28 |
| 封裝： | HEAT SINK, DIP-28 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 269K |
| 代理商： | LB1927 |
LB1927
No.6197-6/11
Pin Description
Pin No.
Pin name
Pin function
Equivalent circuit
28
1
2
OUT1
OUT2
OUT3
Motor drive output pins.
Connect a Schottky diode between these outputs and VCC.
3
GND2
Output ground pin.
5
VM
Output block power supply and output current detection pin.
Connect a resistor (Rf) between this pin and VCC to detect the
output current as a voltage.
The output current is limited according to the equation IOUT =
VRF/Rf.
4
VCC
Power supply pin (except for output block).
6
VREG
Regulated power supply output pin (5V output).
Connect a capacitor (approx. 0.1
F) between this pin and
ground to stabilize the output.
7
PWM
PWM frequency setting pin.
Connect a capacitor between this pin and ground.
C = 3900pF results in a frequency of about 18kHz.
8
CSD
Lock protection circuit operation time setting pin.
Connecting a capacitor of about 10
F between this pin and
ground results in a protection circuit operation time of about
3.3 seconds.
9
10
XI
XO
Crystal oscillator pins.
Connect to quartz oscillator to generate the reference clock.
When an external clock (of several MHz) is used, the clock
signal should be input via a resistor of about 5.1k
connected
in series with the XI pin. In this case, the XO pin must be left
open.
Continued on next page.
相關PDF資料 |
PDF描述 |
|---|---|
| LB1927 | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDIP28 |
| LB8108M | DISK DRIVE MOTOR CONTROLLER, 0.8 A, PQFP44 |
| LB8502M | BRUSH DC MOTOR CONTROLLER, 0.003 A, PDSO10 |
| LB8653T | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO24 |
| LB8658FN | STEPPER MOTOR CONTROLLER, 0.8 A, QCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1927-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1928 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Three-Phase Brushless Motor Driver for Office Automation Equipment - Prel |
| LB1928_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Office Automation Equipment 3-phase Brushless Motor Driver |
| LB1928-E | 功能描述:馬達/運動/點火控制器和驅動器 MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1929 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for OA Products |
發布緊急采購，3分鐘左右您將得到回復。