- 您現在的位置：買賣IC網 > PDF目錄97997 > LB1897H BRUSHLESS DC MOTOR CONTROLLER, PDSO34 PDF資料下載
參數資料
| 型號： | LB1897H |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO34 |
| 封裝： | 0.375 INCH, HSSOP-28 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 159K |
| 代理商： | LB1897H |
LB1897H
No.8804-5/11
Pin Functions
Pin name
Pin no.
Functions
FGIN (+)
9
Non-inverted input pin when FG amp is used as a differential input.
Internal bias application is not made.
FG-CLIP
10
Soft clip control pin of FG amplifier.
C-connection or direct connection of this pin and FG-IN “-“ enables application of soft clip.
FG-OUT
11
FG amp output pin, which functions as an internal resistance load.
CTL
12
Speed control pin. Control is a constant-current drive with current return made from Rf.
Gm = 0.65A/V & 1.50A/VTYP at Rf = 0.5
LIM
13
Current limiting function control pin. This pin voltage enables linear change of the output current.
Gradient = 0.5A/VTYP at Rf = 0.5
FC
14
Frequency characteristics compensation pin for speed control loop.
UIN+, UIN-
VIN+, VIN-
WIN+, WIN-
15, 16
17, 18
19, 20
U-phase hall device input pin. “H” of logic means IN+>IN-.
V-phase hall device input pin. “H” of logic means IN+>IN-.
W-phase hall device input pin. “H” of logic means IN+>IN-.
VCC
21
Power pin for power supply to each circuit other than the output block in IC. This voltage must be stabilized to
prevent entry of ripple and noise.
VS
22
Power pin of the output block.
Rf (PWR)
Rf (SNS)
24
4
Output current detection pin. Connection of Rf between this pin and GND causes current return to the control block.
The lower over-saturation preventive circuit and torque ripple compensation circuit are activated with this pin voltage.
In particular, as the lower over-saturation preventive level is set, extreme lowering of the Rf value causes the lower
over-saturation prevention less effective in the large current range. Be sure to connect PWR and SENSE pins.
UOUT
VOUT
WOUT
27
28
1
U-phase output pin.
V-phase output pin.
(Spark killer Di incorporated)
W-phase output pin.
GSENSE
5
GND sensing pin.
Connection of this pin to GND near the Rf resistor side of the motor GND wiring including Rf enables elimination of
the effect of GND common impedance on Rf. (Do not keep it OPEN.)
FR
6
Forward/backward selector pin.
With this pin voltage, forward/backward can be selected.
(Vth = 2.5VTYP at VCC = 5V)
GND
7, 23
GND other than output transistor.
The minimum potential of output transistor is at the Rf pin.
FGIN (-)
8
Input pin to use the FG amp with inverted input. Return resistor to be connected relative to FTG-OUT.
相關PDF資料 |
PDF描述 |
|---|---|
| LB1927 | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDIP28 |
| LB1927 | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDIP28 |
| LB8108M | DISK DRIVE MOTOR CONTROLLER, 0.8 A, PQFP44 |
| LB8502M | BRUSH DC MOTOR CONTROLLER, 0.003 A, PDSO10 |
| LB8653T | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB18SST | 制造商:Thomas & Betts 功能描述:1/2 CONDUIT BODY,316SS,LB,FORM 8 |
| LB-1904 | 制造商:Ideal Industries Inc 功能描述:WIRE STOP FOR ERGO STRIPMASTER TOOL |
| LB1909M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Linear IC Stepping Motor Driver IC |
| LB1909MC | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC Stepping Motor Driver IC |
| LB1909MC-AH | 功能描述:馬達/運動/點火控制器和驅動器 Step Motor Driver IC for 2-phase Excit RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。