- 您現在的位置：買賣IC網 > PDF目錄358748 > LB1875 (Sanyo Electric Co.,Ltd.) Polygon Mirror Motor Predriver IC PDF資料下載
參數資料
| 型號： | LB1875 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Polygon Mirror Motor Predriver IC |
| 中文描述： | 多邊形鏡電機預驅動器集成電路 |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 207K |
| 代理商： | LB1875 |
LB1875
No. 6002-10/17
Oscillator frequency (MHz)
C1 (
μ
F)
C2 (pF)
C3 (pF)
R1 ( )
2 to 3
0.1
10
100
330k
3 to 7
0.1
None
47
330k
7 to 9
0.1
None
22
330k
9 to 10
0.1
None
12
330k
4. Reference clock
Since the clock input of the PLL circuit (CLK
IN
) and the internal divisor output (CLK
OUT
) are separate, various applications are
possible.
(1) Using the internal divider circuit
Basically, CLK
IN
and CLK
OUT
are shorted. If a division ratio other than the built-in ratio is required, an external divider circuit can be
inserted between these two pins.
[1] Using a quartz oscillator
An oscillator using a quartz crystal and C, R components can be configured as shown below.
The circuit configuration and values are for reference only. The quartz crystal characteristics as well as the possibility of floating
capacitance and noise due to layout factors must be taken into consideration when designing an actual application.
[Precautions for wiring layout design]
Since the quartz oscillator circuit operates at high frequencies, it is susceptible to the influence of floating capacitance from the
circuit board. Wiring should be kept as short as possible and traces should be kept narrow.
[2] External clock input (equivalent to quartz oscillator, several MHz)
When using an external signal source instead of a quartz oscillator, a resistor of about 13 k
should be inserted in series at the X
I
input. The XO pin should be left open.
Signal input level
Low: 0 to 0.8 V
High: 2.5 to 5 V
(2) When not using the internal divider circuit
When using an external signal source to supply a signal equivalent to the FG frequency (several kHz), the signal is input via the
CLK
IN
pin. When not using a quartz oscillator, the X
I
pin should be left open or connected to the V
REG
pin (XO is open).
5. Hall input signal
The Hall input requires a signal with an amplitude of at least the hysteresis width (24 mV max.). Taking possible noise influences
into consideration, an amplitude of at least 100 mV is desirable. If noise at the Hall input is a problem, a noise-canceling capacitor
(about 0.001 to 0.1
μ
F) should be connected across the Hall input pins .
Since the same-phase input range is 0 to V
CC
–2V, a Hall element can be connected in series if 12V is applied at the V
CC
pin.
6. FG input signal
The FG input is designed mainly for input from a Hall element and has the same specifications as the Hall input. If the input is to be
used for an FG pattern or other very low-level signal, an external amplifier must be used to amplify the signal first.
When there is noise at the FG input, locking may be impaired and jitter may increase. If PWM switching noise or other noise is found
to be present, countermeasures such as making the Hall element power supply more stable or connecting a capacitor across the input
will be necessary.
(Reference values)
C1, R1 : For stable oscillation
C2 : For overtone oscillation prevention
C3
: For crystal coupling
XI
XO
VREG
C1
C2
C3
R1
A11349
相關PDF資料 |
PDF描述 |
|---|---|
| LB1876 | Three-Phase Brushless Motor Driver for Polygon Mirror Motors |
| LB1877 | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
| LB1877M | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
| LB1877V | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
| LB1881M | Three-Phase Brushless Motor Driver IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1876 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for Polygon Mirror Motors |
| LB1876(36SOP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LB1876_09 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Polygon Mirror Motors 3-phase Brushless Motor Driver |
| LB1876-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1876-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。