- 您現在的位置：買賣IC網 > PDF目錄358747 > LB1862M (Sanyo Electric Co.,Ltd.) Single-Phase Full-Wave Driver for Fan Motors PDF資料下載
參數資料
| 型號： | LB1862M |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Single-Phase Full-Wave Driver for Fan Motors |
| 中文描述： | 單相全波的風扇馬達驅動器 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 110K |
| 代理商： | LB1862M |
Design Notes
1. V
CC
pin
This pin provides power for motor drive and the control circuits.
The LB1862M supports a wide range of operating voltages, from 3.8 to 16.8 V, and thus can be used in applications
that support both 5-V and 12-V systems.
2. OUT1 and OUT2 pins
Single-phase coil outputs.
The output is a high side inverted, low side single bipolar output. Since a regeneration circuit is included on chip, the
kickback current is regenerated across the low side NPN output even if a diode is used to protect the circuit against
being destroyed by reversed polarity connection.
3. IN
–
and IN
+
pins
Hall element inputs.
The Hall signal is amplified to be a square wave by the Hall amplifier, which has hysteresis characteristics.
A hysteresis of ±3.5 mV (typical) is applied. A Hall input signal amplitude of 70 mV or higher is recommended.
4. CT pin
The capacitor connected between this pin and ground forms a protection circuit that prevents coil burnout if the motor
locks.
If the motor load returns to an appropriate level, the automatic recovery circuit will restart motor rotation. The lock
detection time can be set by changing the value of the capacitor.
If a 0.47 μF capacitor is used:
Lock detection time:
Lock protection time/automatic recovery time: About 0.16 second (output on)
About 0.5 second
About 1 second (output off)
This pin should be tied to ground if the lock protection function is not used.
5. RD pin
This is an open collector output that is low while the motor is turning and high impedance when the locked state is
detected.
This is a latch type output that holds the output high-impedance state if motor rotation is not restarted by the
automatic recovery circuit.
6. ST and HB pins
ST pin: Stops motor drive when a high level is input.
When ST is high, the RD pin output will go to the high-impedance state indicating lock protection mode.
HB pin: Switches the Hall bias. When a high level is input to the ST pin, applications should switch the Hall bias to
suppress standby mode current drain.
Both these pins should be left open if unused.
7. Thermal shutdown circuit
This circuit protects the IC by limiting the output current if the IC internal temperature reaches Tj = 180°C.
No. 5657-5/6
LB1862M
相關PDF資料 |
PDF描述 |
|---|---|
| LB1862 | Fan Motor Single-Phase Full-Wave Driver |
| LB1863M | Two-Phase Unipolar Brushless Motor Driver Automatic Recovery Type Circuit in a Miniature Flat Package |
| LB1868M | RES 10.0MEGOHM MTL FLM.40W 1% TR |
| LB1868 | Two-Phase Brushless Fan Motor Driver |
| LB1870 | Three-Phase Brushless Motor Driver(3相位無電刷馬達驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1862M_09 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Fan Motor Single-Phase Full-Wave Driver |
| LB1862MC | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC For Fan Motor Single-Phase Full-Wave Driver |
| LB1862MC-AH | 功能描述:馬達/運動/點火控制器和驅動器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1863M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Two-Phase Unipolar Brushless Motor Driver Automatic Recovery Type Circuit in a Miniature Flat Package |
| LB1863M_09 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Two-Phase Unipolar Brushless Motor Driver Automatic Recovery Type Circuit in a Miniature Flat Package |
發布緊急采購，3分鐘左右您將得到回復。