- 您現在的位置：買賣IC網 > PDF目錄358744 > LB11921T (Sanyo Electric Co.,Ltd.) Monolithic Digital IC Three-Phase Brushless Motor Driver PDF資料下載
參數資料
| 型號： | LB11921T |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Monolithic Digital IC Three-Phase Brushless Motor Driver |
| 中文描述： | 單片數字集成電路三相無刷電機驅動器 |
| 文件頁數： | 17/18頁 |
| 文件大?。?/td> | 190K |
| 代理商： | LB11921T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁
LB11921T
No.A0604-17/18
18. R and C Pin External Components
The maximum range over which the reference signal frequency fVCO can be varied when 5V is used as the VCC
supply voltage is about a factor of three.
When it is desirable to make this range as wide as possible, since the values of the R pin external resistor (R) and the
C pin external capacitor (C) are determined by the maximum value of the reference signal frequency (fVCO1) and
the minimum value (VCCL) of the VCC power supply due to unit-to-unit variations, R and C can be determined
using the following procedure as a reference.
(1) Calculate R1 and C1 using the following formulas and determine values for R and C such that the conditions R
≤
R1 and C
≤
C1 will hold taking the sample-to-sample variations (including other issues such as temperature
characteristics) into account.
R1 = (VCCL-2.2 V)/370μA
C1 = (370μA /0.9V) × (1/fVCO1) × 0.7
(2) The minimum value (fVCO2) for the reference signal frequency that can be set for the R and C values determined
in step (1) can be calculated from the following formula if we let R2 and C2 be the smallest values for R and C
due to the sample-to-sample variations (including other issues such as temperature characteristics). Therefore, the
range over which the reference signal frequency can be set is fVCO1 to fVCO2.
fVCO2 = 0.38/(R2 × C2)
(3) The following are the conditions that must be met and the points that require care when determining the values of
the external components connected to the R and C pins.
1. The maximum value of the set reference signal frequency must not exceed 1.2MHz.
2. The R pin voltage and the FIL pin voltage must be in the range 0.3V to (VCCL-2.2V). (VCCL is the lowest
value of the VCC supply voltage given the unit-to-unit variations. VCCL is always greater than or equal to
4.4V.) However, the lower the R pin voltage, the more susceptible the system will be to ground line noise, and
the reference signal frequency may become unstable as a result. Therefore the lower end of the R pin voltage
range must not be used if there is much ground line noise in the system.
3. Set the value of the R pin external resistor to a value in the range 5.6k
to 10k
. Also, assure that the R pin
current remains under 370μA.
4. Set the value of the C pin external capacitor to a value in the range 220pF to 1000pF.
5. When it is desirable to make the range of the reference signal frequency as wide as possible, set the values of R
and C to the largest possible values. (However, those values must be lower than the calculated values R1 and
C1.) Use components with the smallest sample-to-sample variations possible. The VCC voltage must be made
as much higher than 5V as possible to acquire the widest possible range for the reference signal frequency.
19. NC pin
Since the NC pins are electrically open with respect to the IC itself, they can be used as intermediate connection
points for lines in the PCB pattern.
相關PDF資料 |
PDF描述 |
|---|---|
| LB11922 | MONOLITHIC DIGITAL TRANSISTOR |
| LB11946 | PWM Current Control Stepping Motor Driver |
| LB11948T | Monolithic Digital IC PWM Constant Current Control 1-2 Phase Excitation Stepping Motor Driver |
| LB11970FV | Monolithic Digital IC For Fan Motor Single-phase Full-wave Driver |
| LB11972V | LB11972V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11921T-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11921T-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 PWM STRUCTURE PRE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11922 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:MONOLITHIC DIGITAL TRANSISTOR |
| LB11922_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For OA Products Three-Phase Brushless Motor Driver |
| LB11922-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。