- 您現在的位置：買賣IC網 > PDF目錄43902 > LB11889M BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO36 PDF資料下載
參數資料
| 型號： | LB11889M |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO36 |
| 封裝： | 0.375 INCH, MFP-36 |
| 文件頁數： | 7/11頁 |
| 文件大小： | 90K |
| 代理商： | LB11889M |
LB11889M
No.8791-5/11
Pin Functions
Pin name
Pin no.
Functions
FGIN (-)
3
Input pin for the FG amplifier to be used with inverted input.
A feedback resistor is connected between this pin and FG OUT.
FGIN (+)
4
Noninverting input pin for the FG amplifier to be used as differential input. No bias is applied internally.
FG-OUT
5
FG amplifier output pin with resistive load internally.
CTL
6
Speed control pin. Control is performed by means of constant current drive which is applied by current feedback from Rf.
Gm = 0.65A/V & 1.50A/V TYP at Rf = 0.5
CTLREF
7
Control reference voltage pin. The voltage is set at approximately VCC/2 internally, but can be varied by applying a
voltage through a low impedance. (The input impedance is approximately 2.5k
.)
LIM
8
Current limiter function control pin. This pin voltage is capable of varying the output current linealy.
Slope = 0.5A/V TYP at Rf = 0.5
FC
9
Speed control loop’s frequency characteristics correction pin.
UIN+, UIN-
VIN+, VIN-
WIN+, WIN-
10, 11
12, 13
14, 15
U phase hall element input pin. “H” for logic represents IN+>IN-.
V phase hall element input pin. “H” for logic represents IN+>IN-.
W phase hall element input pin. “H” for logic represents IN+>IN-.
VCC
16
Power supply pin used to supply to each circuit other than the output blocks inside the IC.
This voltage must be stabilized to reject noise and ripple.
VS
21
Power supply pin for output blocks.
ADJ
22
Pin to be used to adjust the torque ripple correction factor externally.
When adjusting the correction factor, apply voltage externally to the ADJ pin through a low impedance.
Increasing the applied voltage decreases the correction factor ; lowering the applied voltage increases the correction
factor.
The rate of change, when left open, ranges approximately from 0 to 2 times.
(Approximately VCC/2 is set internally and the input impedance is approximately 5k.)
Rf (PWR)
Rf (SNS)
23
31
Output current detection pins. Current feedback is provided to the control blocks by connecting Rf between the pins and
GND. The operation of the lower over-saturation prevention circuit and torque ripple correction circuit depends on the pin
voltage.
In particular, since the oversaturation prevention level is set by the pin voltage, decreasing the Rf value extremely may
cause the lower over-saturation prevention to work less efficiently in the large current region. The PWR pin and SENSE
pin must be connected.
UOUT
VOUT
WOUT
26
27
28
U phase output pin
V phase output pin
(With spark killer diode built in)
W phase output pin
GSENSE
32
GND sensing pin.
By connecting this pin to GND in the vicinity of the Rf resistor side of the Rf included motor GND wiring, the influence
that the GND common impedance exerts on Rf can be excluded. (Must not be left open.)
FR
33
Forward/reverse select pin.
This pin voltage determines forward/reverse. (Vth = 2.5V typ. At VCC = 5V)
GND
34
GND for other than output transistors.
The lowest potential of output transistors is on the Rf pin.
相關PDF資料 |
PDF描述 |
|---|---|
| LB11946 | STEPPER MOTOR CONTROLLER, 1.2 A, PDIP28 |
| LB11946 | STEPPER MOTOR CONTROLLER, 1.2 A, PDIP28 |
| LB11980H | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO28 |
| LB11980H | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO28 |
| LB11999 | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB-1189 | 制造商:Ideal Industries Inc 功能描述:GRIPPER-SET C/STMLT .109/FLPD |
| LB11899J-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11899J-TRM-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB-1190 | 制造商:Ideal Industries Inc 功能描述: |
| LB11920 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for Office Equipment Applications |
發布緊急采購，3分鐘左右您將得到回復。