- 您現在的位置：買賣IC網 > PDF目錄97997 > LB11852FV AC MOTOR CONTROLLER, 0.02 A, PDSO20 PDF資料下載
參數資料
| 型號： | LB11852FV |
| 元件分類： | 運動控制電子 |
| 英文描述： | AC MOTOR CONTROLLER, 0.02 A, PDSO20 |
| 封裝： | 0.225 INCH, SSOP-20 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 142K |
| 代理商： | LB11852FV |
LB11852FV
No.A1112-7/12
Description of Pre-driver Bock
*1 : Power-GND wiring
The SGND is connected to the control circuit power supply system.
*2 : Power stabilization capacitor
For the power stabilization capacitor on the signal side, use a capacitor of 0.1
μF or more. Connect the capacitor
between VCC and GND with a thick and along the shortest possible route.
*3 : Power-side power stabilization capacitor
For the power-side power stabilization capacitor, use a capacitor of 1
μF or more. Connect the capacitor between the
power-side power supply and GND with a thick and along the shortest possible route.
*4 : IN+, IN- pins
Hall signal input pins
Wiring should be short to prevent noise from being carried.
If noise is carried, insert a capacitor between the IN+ and IN- pins.
The Hall input circuit functions as a comparator with hysteresis (15mV).
It also has a soft switch zone with
±30mV (input signal difference voltage).
It is also recommended that the Hall input level should be a minimum of 100mV (p-p).
*5 : CPWM pin
Pin to connect the capacitor used to generate the PWM basic frequency
Use of CP = 200pF causes oscillation at f = 30kHz, which is the basic frequency of PWM.
As this is also used for the current limiter reset signal, a capacitor must be connected even if the speed is not going to
be controlled.
*6 : CT pin
Pin to connect the capacitor used for lock detection
The constant-current charging and constant-current discharging circuits incorporated cause locking when the pin
voltage reaches 3.0V, and releasing the lock protection when it drops to 1.0V.
Connect this pin to the GND when it is not to be used (locking not necessary).
*7 : SENSE pin
Current limiter detection pin
When the pin voltage exceeds 0.21V, the current limiter is activated, and operation enters lower regeneration mode.
Connect this pin to the GND when it is not to be used.
*8 : FG pin
Rotational speed detection pin
This is an open collector output that can detect the rotational speed using the FG output corresponding to the phase
changeover.
Keep this pin open when it is not to be used.
相關PDF資料 |
PDF描述 |
|---|---|
| LB11884 | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO48 |
| LB11885 | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO48 |
| LB11947 | BRUSH DC MOTOR CONTROLLER, 1.75 A, PDIP28 |
| LB11948T | STEPPER MOTOR CONTROLLER, 0.5 A, PDSO30 |
| LB1814M | DISK DRIVE MOTOR CONTROLLER, 1 A, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11852FV-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11852FV-MPB-H | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11852FV-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11852FV-TLM-H | 功能描述:馬達/運動/點火控制器和驅動器 FAN MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11852RV-MPB-H | 制造商:ON Semiconductor 功能描述:SINGLE PHASE MOTOR DRIVER - Ammo Pack |
發布緊急采購，3分鐘左右您將得到回復。