- 您現在的位置：買賣IC網 > PDF目錄97996 > LB11826 BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, DFM28 PDF資料下載
參數資料
| 型號： | LB11826 |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, DFM28 |
| 封裝： | DIP-28 |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 129K |
| 代理商： | LB11826 |
LB11826
No.7109-9/11
Continued from preceding page.
Pin No.
Pin name
Pin function
Equivalent circuit
22
21
24
23
26
25
IN1+
IN1-
IN2+
IN2-
IN3+
IN3-
Hall amplifier input.
IN+ > IN- is the input high state, and the reverse is
the input low state.
It is recommended that the Hall signal has an
amplitude of 100mVp-p (differential) or more.
Connect a capacitor between the IN+ and IN- inputs
if there is noise in the Hall sensor signals.
300
Ω
300
Ω
22 24 26
21 23 25
VREG
27
F/R
Forward/reverse control pin.
Low : 0V to 1.5V
High : 3.5V to VREG
H level when open.
Hysteresis width about 0.5V.
27
VREG
2k
Ω
22k
Ω
LB11826 Description
1. Speed control circuit
This IC performs speed control by using both the speed discriminator circuit and PLL circuit. The speed control circuit
outputs the error signal once for every two cycles of FG (one FG cycle counted). The PLL circuit outputs the phase
error signal once for each cycle of FG.
As the FG servo frequency is calculated as follows, the motor speed is set with the number of FG pulses and clock
frequency.
fFG (servo) = fCLK/512
fCLK : Clock frequency
This IC achieves variable speed control with ease when combined with LB11825M.
2. Output drive circuit
This IC employs a direct PWM drive method to minimize the power loss at output. The output Tr is always saturated at
ON, and the motor drive force is adjusted through change of the duty at which the output is turned ON. Since the output
PWM switching is made with the lower-side output Tr, it is necessary to connect the schottky diode between OUT and
VCC (because the through current flows at an instant when the lower-side Tr is turned ON if the diode with a short
reverse recovery time is not used). The diode between OUT and GND is incorporated. When the large output current
presents problem (waveform disturbance at kickback on the lower side), connect a commutating diode or schottky
diode externally.
3. Current limiting circuit
The current limiting circuit performs limiting with the current determined from I = VRF/Rf (VRF = 0.5Vtyp, Rf :
current detector resistance) (that is, this circuit limits the peak current).
Limiting operation includes decrease in the output on-duty to suppress the current.
4. Power save circuit
This IC enters the power save condition to decrease the current dissipation in the stop mode. In this condition, the bias
current of most of circuits is cut off. Even in the power save condition, the 5 V regulator output is given.
5. Reference clock
This is entered from the external signal source (1MHz max) via a resistor (reference : about 5.1k
Ω) in series with the XI
pin. The XO pin is left open.
Input signal source levels :
Low-level voltage : 0 to 0.8V
High-level voltage : 2.5 to 5.0V
相關PDF資料 |
PDF描述 |
|---|---|
| LB11850VA | AC MOTOR CONTROLLER, PDSO24 |
| LB11850VA | AC MOTOR CONTROLLER, PDSO24 |
| LB11852FV | AC MOTOR CONTROLLER, 0.02 A, PDSO20 |
| LB11884 | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO48 |
| LB11885 | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11826_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For OA Products Three-Phase Brushless Motor Driver |
| LB11826-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11827 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for OA Products |
| LB11847 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Current Control Type Stepping Motor Driver |
| LB11847_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Current Control Type Stepping Motor Driver |
發布緊急采購，3分鐘左右您將得到回復。