- 您現在的位置：買賣IC網 > PDF目錄383255 > L9950TR (意法半導體) DOOR ACTUATOR DRIVER PDF資料下載
參數資料
| 型號： | L9950TR |
| 廠商： | 意法半導體 |
| 英文描述： | DOOR ACTUATOR DRIVER |
| 中文描述： | 門執行器驅動 |
| 文件頁數： | 14/23頁 |
| 文件大小： | 231K |
| 代理商： | L9950TR |
L9950
14/23
Bit
Input Register 1 (write)
Status Register 1 (read)
Name
Comment
Name
Comment
22
OUT11 OC
Recovery Enable
In case of an over-current event the
over-current status bit (Status
Register 0) is set and the output is
switched off. If the over-current
Recovery Enable bit is set the
output will be automatically
reactivated after a delay time
resulting in a PWM modulated
current with a programmable duty
cycle (Bit 21 of Input Data Register
0).
Depending on occurance of
Overcurrent Event and internal
clock phase it is possible that one
recovery cycle is executed even if
this bit is set to zero.
VS overvoltage
In case of an overvoltage or
undervoltage event the
corresponding bit is set and
the outputs are deactivated.
If VS voltage recovers to
normal operating conditions
outputs are reactivated
automatically.
21
OUT10 OC
Recovery Enable
VS undervoltage
20
OUT9 OC
Recovery Enable
Thermal shutdown
In case of an thermal
shutdown all outputs are
switched off. The
microcontroller has to clear
the TSD bit by setting the
Reset Bit to reactivate the
outputs.
19
OUT8 OC
Recovery Enable
Temperature warning
This bit is for information
purpose only. It can be used
for a thermal management by
the microcontroller to avoid a
thermal shutdown.
18
OUT7 OC
Recovery Enable
Not Ready Bit
After switching the device
from standby mode to active
mode an internal timer is
started to allow chargepump
to settle before the outputs
can be activated. This bit is
cleared automatically after
start up time has finished.
Since this bit is controlled by
internal clock it can be used
for synchonizing testing
events(e.g. measuring filter
times).
Table 9. SPI - Input Data and Status Register
(continued)
相關PDF資料 |
PDF描述 |
|---|---|
| L9951 | DOOR ACTUATOR DRIVER |
| L9997 | DUAL HALF BRIDGE DRIVER |
| L9997ND013TR | DUAL HALF BRIDGE DRIVER |
| LCDP1511D | DUAL LINE PROGRAMMABLE TRANSIENT VOLTAGE SUPPRESSOR FOR SLIC PROTECTION |
| LCDP1521 | DUAL LINE PROGRAMMABLE TRANSIENT VOLTAGE SUPPRESSOR FOR SLIC PROTECTION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9950XP | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9950XPTR | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9951 | 功能描述:馬達/運動/點火控制器和驅動器 REAR DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9951_10 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Rear door actuator driver |
| L-995-12 | 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:NylaKrimp? Funnel Entry Ring Tongue Terminal for 4/0 AWG Wire, Stud #12 |
發布緊急采購，3分鐘左右您將得到回復。