- 您現在的位置：買賣IC網 > PDF目錄383255 > L9904 (意法半導體) MOTOR BRIDGE CONTROLLER PDF資料下載
參數資料
| 型號： | L9904 |
| 廠商： | 意法半導體 |
| 英文描述： | MOTOR BRIDGE CONTROLLER |
| 中文描述： | 汽車橋控制器 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 268K |
| 代理商： | L9904 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁
15/17
L9904
FUNCTIONAL DESCRIPTION
(continued)
Programmable cross conduction protection
The external power MOS transistors in H-Bridge ( two half bridges) configuration are switched on with an addi-
tional delay time t
CCP
to prevent cross conduction in the halfbridge. The cross conduction protection time
t
CCP
is determined by the external capacitor C
PR
and resistor R
PR
at the PR pin. The capacitor C
PR
is charged
up to the voltage limit V
PRH
. A level change on the control inputs DIR and PWM switches off the concerned ex-
ternal MOS transistor and the charging source at the PR pin. The resistor R
PR
discharges the capacitor C
PR
.
The concerned external power MOS transistor will be switched on again when the voltage at PR reaches the
value of V
PRL
. After that the CPR will be charged again. The capacitor C
PR
should be choosen between 100pF
and 1nF. The resistor R
PR
should be higher than 7kW. The delay time can be expressed as follows:
t
CCP
= R
PR
· C
PR
· ln N
PR
with N
PR
= V
PRH
/ V
PRL
= 2
t
CCP
= 0.69 · R
PR
· C
PR
ISO-Interface
The ISO-Interface provides the communication between the micro controller and a serial bus with a baud rate
up to 60kbit/s via a single wire which is V
BAT
and GND compatible. The logic level transmission input TX drives
the open drain K-output. The K output can be connected to a serial bus with a pull up resistor to V
BAT
. The K-
pin is protected against overvoltage, short to GND and VS and can be driven beyond V
VS
and GND. During lack
of V
VS
or GND the output shows high impedance characteristic. The open drain output RX with an internal pull
up resistor monitors the status at the K-pin to read the received data and control the transmitted data. Short
circuit condition at K-pin is recognized if the internal open drain transistor isn't able to pull the voltage potential
at K-pin below the threshold of 0.45·V
VS
. Then the RX stays in high condition. A timer starts and switches the
open drain transistor after typ. 20μs off. A next low at the TX input resets the timer and the open drain transistor
switches on again.
Figure 8. Functional schematic of the ISO-interface
RX
TX
K
VCC
RRX
0.5
VVS
TX
R
TSH
delay
=
R
S
Q
R
I
KH
相關PDF資料 |
PDF描述 |
|---|---|
| L9907 | MOTOR BRIDGE FOR HEADLIGHT ADJUSTMENT |
| L9907N | MOTOR BRIDGE FOR HEADLIGHT ADJUSTMENT |
| L9907ND | MOTOR BRIDGE FOR HEADLIGHT ADJUSTMENT |
| L9909 | DC MOTOR DRIVER WITH POSITION CONTROL |
| L9911 | CAR ALTERNATOR MULTIFUNCTION SMART VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9904TR | 功能描述:馬達/運動/點火控制器和驅動器 Motor Bridge Contlr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9906 | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Motor Control Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9906TR | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Motor Control Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9907 | 制造商:HAMAMATSU 功能描述:IR EMITTER 660NM |
| L9907N | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MOTOR BRIDGE FOR HEADLIGHT ADJUSTMENT |
發布緊急采購，3分鐘左右您將得到回復。