- 您現在的位置：買賣IC網 > PDF目錄43901 > L9903 (STMICROELECTRONICS) BRUSH DC MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | L9903 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, PDSO20 |
| 封裝： | SO-20 |
| 文件頁數： | 6/17頁 |
| 文件大小： | 269K |
| 代理商： | L9903 |
L9903
14/17
tCCP= RPR CPR ln NPR
with NPR= VPRH / VPRL = 2
tCCP= 0.69 RPR CPR
3.14 ISO-Interface
The ISO-Interface provides the communication between the micro controller and a serial bus with a baud rate
up to 60kbit/s via a single wire which is VBAT and GND compatible. The logic level transmission input TX drives
the open drain K-output. The K output can be connected to a serial bus with a pull up resistor to VBAT. The K-
pin is protected against overvoltage, short to GND and VS and can be driven beyond VVS and GND. During lack
of VVS or GND the output shows high impedance characteristic. The open drain output RX with an internal pull
up resistor monitors the status at the K-pin to read the received data and control the transmitted data. Short
circuit condition at K-pin is recognized if the internal open drain transistor isn't able to pull the voltage potential
at K-pin below the threshold of 0.45VVS. Then the RX stays in high condition. A timer starts and switches the
open drain transistor after typ. 20s off. A next low at the TX input resets the timer and the open drain transistor
switches on again.
Figure 11. Functional schematic of the ISO-interface
RX
TX
K
VCC
R RX
0.5
VVS
TX
R
TSH
delay
=
R
S
Q
R
IKH
相關PDF資料 |
PDF描述 |
|---|---|
| L9903TR | BRUSH DC MOTOR CONTROLLER, PDSO20 |
| L9911B | BRUSH DC MOTOR CONTROLLER, SFM8 |
| L9911A | BRUSH DC MOTOR CONTROLLER, SFM8 |
| L9911 | BRUSH DC MOTOR CONTROLLER, SFM8 |
| L9942XPTR | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9903TR | 功能描述:馬達/運動/點火控制器和驅動器 Motor Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9904 | 功能描述:馬達/運動/點火控制器和驅動器 Motor Bridge Contlr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9904TR | 功能描述:馬達/運動/點火控制器和驅動器 Motor Bridge Contlr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9906 | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Motor Control Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9906TR | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Motor Control Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。