- 您現在的位置：買賣IC網 > PDF目錄97996 > L9524C-TR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PDSO24 PDF資料下載
參數資料
| 型號： | L9524C-TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| 封裝： | LEAD FREE, SOP-24 |
| 文件頁數： | 7/27頁 |
| 文件大?。?/td> | 410K |
| 代理商： | L9524C-TR |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
L9524C
Functional description
15/27
Though in mode 2 (relay mode, serial diagnostic interface protocol) the relay should be
switched permanently the L9524C also expects a PWM signal at the CI pin since the serial
diagnostic interface protocol is synchronized by falling edges of the CI signal (see section
“Diagnostic output”). The relay then is switched on permanently if the off time (time between
rising and falling edge) of the PWM signal is less than tIO sup since the relay output
suppresses pulses shorter than tIO sup (see section “Relay output”). For the same reason the
relay is switched off permanently if the on time (time between falling and rising edge) of the
PWM signal is less than tIO sup. In all other cases the relay is switched according to the
PWM signal at the CI pin.
Figure 6.
Control input signal in mode 2 for permanent switch on
In mode 1 (relay mode, go/no-go diagnostic interface protocol) no edges are necessary for
the go/no-go protocol. Therefore the relay is switched on if VCI = VCI on and it is switched off
if VCI = VCI off.
4.4
Diagnostic output
The diagnostic output stage of the L9524C (DO pin) consists of a current-limited low-side
switch and a pull-up resistor RDO to the VS pin. The voltage level of a logical low signal VDOL
is given by the drop across the low-side switch and the voltage level of a logical high signal
is equal to VVS.
The L9524C is able to detect the following failures (see sections “Supply”, “Current
monitoring”, and “Switch monitoring”):
●
open-load (6 glow plugs),
●
overcurrent (6 glow plugs, stored until power-down),
●
any switch is defect (4 switches),
●
supply voltage (VVS) is too low (“under voltage”),
●
supply voltage (VVS) is too high (“over voltage”),
●
junction temperature (TJ) is too high,
●
charge pump voltage (VCP) is too low (“charge pump under voltage”), and
●
battery voltage (VBAT) is too low (“battery under voltage”).
V
CI
t
V
CI off
V
CI on
0.6 . V
VS
0.4 . V
VS
t
relay
ON
OFF
T
CI
t
IO sup
t
IO sup
t
CI fil +tdel
相關PDF資料 |
PDF描述 |
|---|---|
| L9949 | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO20 |
| L99PD08TR | POWER SUPPLY MANAGEMENT CKT, PQFP32 |
| L99PD08 | POWER SUPPLY MANAGEMENT CKT, PQFP32 |
| LA120X1/2-1 | FAST BLOW ELECTRIC FUSE, 0.5A, 1200VAC, 1000VDC, 100000A (IR), INLINE/HOLDER |
| LA50QS900-4 | FAST BLOW ELECTRIC FUSE, 900A, 500VAC, 500VDC, 200000A (IR), INLINE/HOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L952GD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| L952HD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| L952YD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| L9534 | 制造商:Leviton Manufacturing Co 功能描述: |
| L9536 | 制造商:Leviton Manufacturing Co 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。