- 您現在的位置：買賣IC網 > PDF目錄383254 > L9468 (意法半導體) ALL SILICON VOLTAGE REGULATOR PDF資料下載
參數資料
| 型號： | L9468 |
| 廠商： | 意法半導體 |
| 英文描述： | ALL SILICON VOLTAGE REGULATOR |
| 中文描述： | 全硅穩壓器 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 166K |
| 代理商： | L9468 |
5/8
L9468
3
FAULT
The following table lists the conditions that cause the fault lamp driver to function. To prevent lamp flicker, spe-
cific faults are required to be present for TDELAY seconds before the lamp driver is activated. This delay is
indicated in the table.
Table 7.
Table 8.
Regulation Features
Notes:
6.
Lamp and Ignition are cooperative. Either can turn on the device when the other is left open or held low. When both go below
their minimum thresholds the L9468 goes into "L" Terminal Control (LTC). The L9468 will remain in LTC until the phase (P) voltage
drops below VP2 and the frequency drops below fIRF at the VP1 threshold then the L9468 is disabled.
This threshold on the phase signal is used to detect the phase frequency, fIFR, for the Initiation of field regulation.
This threshold on the phase signal is used to sense the presence of the phase for fault detection purposes.
This is the time duration the L9468 takes to rump up from 0 % to 100% duty cycle in response to an increased load on the enerator.
The LRC ratio is set 1:4 and the Vreg comparator status is latched at foundamental frequency rate.
10. Cut-back occurs when both the "L" and "I" terminals are LOW . If the "I" terminal is disconnected it will assume a logic LOW
allowing the "L" terminal to perform the function alone. In cut-back, to prevent the loss of phase signal, a 31.25% duty cycle is
applied to field output when phase drops below Vp2
7.
8.
9.
Conditions
Delay
1. Key-on (wiring check), lamp stays on for 1 ± 0.15 sec regardless
other conditions
No
2. V
GO
/ S> V
OV
Yes
3. V
GO
/ S < undervoltage threshold voltage
AND
Phase frequency > f
LRC
Yes
4. Phase Voltage < VP2
AND
VGO
/ S < setpoint
Yes
5. Phase frequency < f
IFR
Yes
6. No connection between Battery and VGO
No
7. FAILSAFE
Yes
Symbol
Parameter
Test Condition
Min.
Typ.
Max.
Unit
V
LON
Lamp term turn on threshold
6
0.8
1
1.15
V
I
LON
Lamp term current sensitivity
V
L
= 1 V to Vsp
0.09
0.78
mA
V
P1
Initiation of regulation detection
phase voltage threshold
7
I
P
= 1mA (sinking current)
2.5
3
3.5
V
V
P2
Fault detection phase voltage
threshold
8
7
8
9
V
I
P
Sinking current @ P terminal
V
P
= 1.5V
0.5
1
1.8
mA
f
IFR
Initiation of field regulation
frequency
53.04
61
70.15
Hz
FSDF
Field Strobe Duty Factor
@ "power up" with f
PHASE
< f
IFR
31.25
%
LRC
Load Response Control rate
9
2.125
2.5
2.875
s
f
LRC
LRC transition frequency
LRC is enabled below this value
263.5
310
356.5
Hz
V
LCB
"L" term. Cut-Back Setpoint
"L" = 0V, "I" = 0V
10
V
S
-
20%
V
S
-
25%
V
S
-30%
V
相關PDF資料 |
PDF描述 |
|---|---|
| L9468N | ALL SILICON VOLTAGE REGULATOR |
| L9474 | ALL SILICON VOLTAGE REGULATOR |
| L9484 | CAR ALTERNATOR VOLTAGE REGULATOR |
| L9610 | PWM POWER MOS CONTROLLER |
| L9611 | PWM POWER MOS CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9468N | 功能描述:線性穩壓器 - 標準 Silicon Voltage Regulator RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| L9473 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:CAR ALTERNATOR VOLTAGE REGULATOR |
| L9473J | 功能描述:線性穩壓器 - 標準 Car Alternator Voltage Regulator RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| L9474 | 功能描述:線性穩壓器 - 標準 Multifunct Generator RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| L9474N | 功能描述:線性穩壓器 - 標準 Alternator Voltage Reg w/RVC interface RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
發布緊急采購，3分鐘左右您將得到回復。