參數資料
型號: L6997D
廠商: STMICROELECTRONICS
元件分類: 穩壓器
英文描述: SWITCHING CONTROLLER, PDSO20
封裝: MO-153AC, TSSOP-20
文件頁數: 3/30頁
文件大?。?/td> 591K
代理商: L6997D
Obsolete
Product(s)
- Obsolete
Product(s)
11/30
L6997
4.6 Protection and fault
The load protection is realized by using the VSENSE pin. Both OVP and UVP are latched, and the fault condition
is indicated by the PGOOD and the OVP pins. If the output voltage is between the 89% (typ.) and 110% (typ)
of the regulated value, PGOOD is high. If a hard overvoltage or an undervoltage occurs, the device is latched:
low side MOSFET and, high side MOSFET are turned off and PGOOD goes low. In case the system detects an
overvoltage the OVP pin goes high.
To recover the functionality the device must be shut down and restarted the SHDN pin, or by removing the sup-
ply, and restarting the devicewith the correct sequence.
4.7 Drivers
The integrated high-current drivers allow using different size of power MOSFET, maintaining fast switching tran-
sitions. The driver for the high side MOSFET uses the BOOT pin for supply and PHASE pin for return (floating
driver). The driver for the low side MOSFET uses the VDR pin for the supply and PGND pin for the return. The
drivers have the adaptive anti-cross-conduction protection, which prevents from having bothhigh side and low
side MOSFET on at the same time, avoiding a high current to flow from VIN to GND. When high side MOSFET
is turned off the voltage on the PHASE pin begins to fall; the low side MOSFET is turned on only when the volt-
age on PHASE pin reaches 250mV. When low side is turned off, high side remains off until LGATE pin voltage
reaches 500mV. This is important since the driver can work properly with a large range of external power MOS-
FETS.
The current necessary to switch the external MOSFETS flows through the device, and it is proportional to the
MOSFET gate charge the switching frequency and the driver voltage. So the power dissipation of the device is
function of the external power MOSFET gate charge and switching frequency.
(14)
The maximum gate charge values for the low side and high side are given by:
(15)
(16)
Where fSW0 = 500Khz. The equations above are valid for TJ = 150°C. If the system temperature is lower the QG
can be higher.
For the Low Side driver the max output gate charge meets another limit due to the internal traces degradation;
in this case the maximum value is QMAXLS = 125nC.
The low side driver has been designed to have a low resistance pull-down transistor, approximately 0.5 ohms.
This prevents undesired LS MOSFET Turn On during the fast rise-time of the pin PHASE, due to the Miller ef-
fect.
When the 3.3V bus is used to supply the drivers, ULTRA LOGIC LEVEL MOSFETs should be selected , to be
sure that the MOSFETs work in properly way.
P
driver
V
cc
Q
gTOT
F
SW
=
Q
MAXHS
f
SW0
f
SW
------------- 75nC
=
Q
MAXLS
f
SW0
f
SW
------------- 125nC
=
相關PDF資料
PDF描述
L6997DTR SWITCHING CONTROLLER, PDSO20
L7200 DISK DRIVE MOTOR CONTROLLER, 2.6 A, PQFP64
L7250 VOICE COIL MOTOR CONTROLLER, PQFP64
L7980A 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L7980 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
L6997DTR 功能描述:DC/DC 開關控制器 Adjustable Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6997S 功能描述:DC/DC 開關控制器 STEP DOWN CONTROLLER Lo Vltg Operations RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6997STR 功能描述:DC/DC 開關控制器 3.0 to 5.5V Step-Dwn RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6998-0 制造商:Johanson Manufacturing 功能描述:TUNING ELEMENT
L6998-1 制造商:Johanson Manufacturing 功能描述:TUNING ELEMENT