參數資料
型號: L6919E
廠商: STMICROELECTRONICS
元件分類: 穩壓器
英文描述: SWITCHING CONTROLLER, PDSO28
封裝: SO-28
文件頁數: 4/33頁
文件大?。?/td> 644K
代理商: L6919E
Obsolete
Product(s)
- Obsolete
Product(s)
L6919E
12/33
1. TON Limited Output Voltage.
This happens when the maximum ON time is reached before the current in each phase reaches IOCPx (IINFOx
< 35
A).
Figure 5a shows the maximum output voltage that the device is able to regulate considering the TON limitation
imposed by the previous relationship. If the desired output characteristic crosses the TON limited maximum output
voltage, the output resulting voltage will start to drop after crossing. In this case, the device doesn't perform con-
stant current limitation but only limits the maximum ON time following the previous relationship. The output volt-
age follows the resulting characteristic (dotted in Figure 5b) until UVP is detected or anyway until IFB = 70A.
Figure 5. TON Limited Operation
2. Constant Current Operation
This happens when ON time limitation is reached after the current in each phase reaches IOCPx (IINFOx>35A).
The device enters in Quasi-Constant-Current operation: the low-side mosfets stays ON until the current read
becomes lower than IOCPx (IINFOx < 35A) skipping clock cycles. The high side mosfets can be turned ON with
a TON imposed by the control loop at the next available clock cycle and the device works in the usual way until
another OCP event is detected.
This means that the average current delivered can slightly increase also in Over Current condition since the cur-
rent ripple increases. In fact, the ON time increases due to the OFF time rise because of the current has to reach
the IOCPx bottom. The worst-case condition is when the ON time reaches its maximum value.
When this happens, the device works in Constant Current and the output voltage decrease as the load increase.
Crossing the UVP threshold causes the device to latch (FAULT pin is driven high).
Figure 6 shows this working condition
It can be observed that the peak current (Ipeak) is greater than the IOCPx but it can be determined as follow:
Where VoutMIN is the minimum output voltage (VID-30% as follow).
The device works in Constant-Current, and the output voltage decreases as the load increase, until the output
voltage reaches the Under-Voltage threshold (VoutMIN). When this threshold is crossed, all mosfets are turned
off, the FAULT pin is driven high and the device stops working. Cycle the power supply to restart operation. The
maximum average current during the Constant-Current behavior results:
a) Maximum output Voltage
b) TON Limited Output Voltage
0.80VIN
0.40VIN
VOUT
I
OUT
IOCP=2IOCPx
(I
FB=70A)
TON Limited Output
characteristic
0.80VIN
0.40VIN
VOUT
IOUT
IOCP=2IOCPx
(IFB=70A)
Desired Output
characteristic and
UVP threshold
Resulting Output
characteristic
Ipea k
I
OCPx
V
IN
Vo ut
MIN
L
--------------------------------------- Ton
MAX
+
I
OCPx
V
IN
Vo ut
MIN
L
--------------------------------------- 0.40 T
+
==
I
M AX,TOT
2I
MA X
2I
OCPx
Ipe ak
I
OC P x
2
--------------------------------------
+
+
=
相關PDF資料
PDF描述
L6920DTR 1.2 A SWITCHING REGULATOR, PDSO8
L6920D 1.2 A SWITCHING REGULATOR, PDSO8
L6920 1.2 A SWITCHING REGULATOR, PDSO8
L6924D013TR 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16
L6926D 1.4 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
L6919ETR 功能描述:DC/DC 開關控制器 5-Bit Dual Ph Contlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L-692 制造商:RHOMBUS-IND 制造商全稱:Rhombus Industries Inc. 功能描述:Common Mode Inductor
L6920 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1V HIGH EFFICIENCY SYNCRONOUS STEP UP CONVERTER
L6920D 功能描述:直流/直流開關轉換器 0.6 to 5.5V Step-Up RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
L6920DB 功能描述:直流/直流開關轉換器 Synchronous Rectifer Step Up Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT