參數資料
型號： L6911ETR
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20
封裝： SO-20
文件頁數： 7/34頁
文件大?。?/td> 558K
代理商： L6911ETR
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
L6911E
Device description
15/34
5.5
Monitor and protection
The output voltage is monitored by means of pin 1 (VSEN). If it is not within ±10% (typ.) of
the programmed value, the powergood output is forced low.
The device provides overvoltage protection, when the output voltage reaches a value 17%
(typ.) greater than the nominal one. If the output voltage exceed this threshold, the OVP pin
is forced high (5V) and the lower driver is turned on as long as the over-voltage is detected.
The OVP pin is capable to deliver up to 60mA (min) in order to trigger an external SCR
connected to burn the input fuse. The low-side mosfet turn-on implement this function when
the SCR is not used and helps in keeping the ouput low.
To perform the overcurrent protection the device compares the drop across the high side
MOS, due to its
RDSON, with the voltage across the external resistor (ROCS) connected between the
OCSET pin and drain of the upper MOS. Thus the overcurrent threshold (IP) can be
calculated with the following relationship:
Equation 4
where the typical value of IOCS is 200A.
To calculate the ROCS value it must be considered the maximum RDSON (also the variation
with temperature) and the minimum value of IOCS. To avoid undesirable trigger of
overcurrent protection this relationship must be satisfied:
Equation 5
where
I is the inductance ripple current and I
OUTMAX is the maximum output current.
In case of output short circuit the soft start capacitor is discharged with constant current
(10
A typ.) and when the SS pin reaches 0.5V the soft start phase is restarted. During the
soft start the over-current protection is always active and if such kind of event occours, the
device turns off both mosfets, and the SS capacitor is dicharged again after reaching the
upper threshold of about 4V. The system is now working in HICCUP mode, as shown in
Figure 7 on page 16 a. After removing the cause of the over-current, the device restart
working normally without power supplies turn off and on.
I
P
I
OCS
R
OCS
R
DSON
--------------------------------
=
I
P
I
OUTMAX
l
2
-----
+
≥
I
PEAK
=
相關PDF資料
PDF描述
L6924U013 POWER SUPPLY SUPPORT CKT, PQCC16
L6924U013TR POWER SUPPLY SUPPORT CKT, PQCC16
L6924U POWER SUPPLY SUPPORT CKT, QCC16
L6926D1013TR 1.65 A SWITCHING REGULATOR, 800 kHz SWITCHING FREQ-MAX, PDSO8
L6996D SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO24
相關代理商/技術參數
參數描述
L6912-2 制造商:Thomas & Betts 功能描述:1/2 CORD GRIP CONNECTOR,2/BG
L6913-1 制造商:Thomas & Betts 功能描述:1/2 CORD GRIP CONNECTOR,1/BG
L6913-2 制造商:Thomas & Betts 功能描述:1/2 CORD GRIP CONNECTOR,2/BG
L6916D 功能描述:運算放大器 - 運放 POWER SUPPLY RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
L6916DTR 功能描述:運算放大器 - 運放 POWER SUPPLY RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*