參數資料
型號: L6728ATR
廠商: STMICROELECTRONICS
元件分類: 穩壓器
英文描述: SWITCHING CONTROLLER, 660 kHz SWITCHING FREQ-MAX, PDSO10
封裝: 3 X 3 MM, VFDFPN-10
文件頁數: 8/32頁
文件大?。?/td> 1223K
代理商: L6728ATR
Obsolete
Product(s)
- Obsolete
Product(s)
L6728A
Application details
b)
Place FZ1 below FLC (typically 0.5*FLC):
c)
Place FP1 at FESR:
d)
Place FZ2 at FLC and FP2 at half of the switching frequency:
e)
Check that compensation network gain is lower than open loop EA gain before
F0dB;
f)
Check phase margin obtained (it should be greater than 45°) and repeat if
necessary.
9.2
Layout guidelines
L6728A provides control functions and high current integrated drivers to implement high-
current step-down DC-DC converters. In this kind of application, a good layout is very
important.
The first priority when placing components for these applications has to be reserved to the
power section, minimizing the length of each connection and loop as much as possible. To
minimize noise and voltage spikes (EMI and losses) power connections (highlighted in
Figure 7) must be a part of a power plane and anyway realized by wide and thick copper
traces: loop must be anyway minimized. The critical components, i.e. the power MOSFETs,
must be close one to the other. The use of multi-layer printed circuit board is recommended.
The input capacitance (CIN), or at least a portion of the total capacitance needed, has to be
placed close to the power section in order to eliminate the stray inductance generated by the
copper traces. Low ESR and ESL capacitors are preferred, MLCC are suggested to be
connected near the HS drain.
Use proper VIAs number when power traces have to move between different planes on the
PCB in order to reduce both parasitic resistance and inductance. Moreover, reproducing the
same high-current trace on more than one PCB layer will reduce the parasitic resistance
associated to that connection.
Connect output bulk capacitors (COUT) as near as possible to the load, minimizing parasitic
inductance and resistance associated to the copper trace, also adding extra decoupling
capacitors along the way to the load when this results in being far from the bulk capacitors
bank.
C
F
1
π R
F
LC
-----------------------------
=
C
P
C
F
2
π R
F
C
F
ESR
1
----------------------------------------------------------
=
R
S
R
FB
F
SW
2F
LC
------------------
1
---------------------------
=
C
S
1
π R
S
F
SW
-------------------------------
=
相關PDF資料
PDF描述
L6728A SWITCHING CONTROLLER, 660 kHz SWITCHING FREQ-MAX, PDSO10
L6728D 30 A SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO10
L6911C 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20
L6911DTR 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20
L6911E 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20
相關代理商/技術參數
參數描述
L6728D 功能描述:電流型 PWM 控制器 SNGL PHASE PWM CONTROLLER RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
L6728DTR 功能描述:電流型 PWM 控制器 Single-Phase PWM 5V to 12V Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
L6728H 功能描述:電壓模式 PWM 控制器 Sgl Output 300 KHz DFN-10 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
L6728HTR 功能描述:電流型 PWM 控制器 SINGLE PHASE PWM CNTRL PWR GOOD RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
L6728TR 功能描述:DC/DC 開關控制器 Sngl phase PWM controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK