- 您現在的位置：買賣IC網 > PDF目錄384585 > L6727TR (意法半導體) Single phase PWM controller PDF資料下載
參數資料
| 型號： | L6727TR |
| 廠商： | 意法半導體 |
| 英文描述： | Single phase PWM controller |
| 中文描述： | 單相PWM控制器 |
| 文件頁數： | 18/22頁 |
| 文件大小： | 318K |
| 代理商： | L6727TR |
Application details
L6727
18/22
same high-current trace on more than one PCB layer will reduce the parasitic resistance
associated to that connection.
Connect output bulk capacitors (C
OUT
) as near as possible to the load, minimizing parasitic
inductance and resistance associated to the copper trace, also adding extra decoupling
capacitors along the way to the load when this results in being far from the bulk capacitors
bank.
Figure 8.
Power connections (heavy lines)
Gate traces and phase trace must be sized according to the driver RMS current delivered to
the power MOSFET. The device robustness allows managing applications with the power
section far from the controller without losing performances. Anyway, when possible, it is
recommended to minimize the distance between controller and power section. See
Figure 9
for drivers current paths.
Small signal components and connections to critical nodes of the application, as well as
bypass capacitors for the device supply, are also important. Locate bypass capacitor (VCC
and Bootstrap capacitor) and loop compensation components as close to the device as
practical. For over current programmability, place R
OCSET
close to the device and avoid
leakage current paths on COMP / OC pin, since the internal current source is only 60
μ
A.
Systems that do not use Schottky diode in parallel to the Low-Side MOSFET might show big
negative spikes on the phase pin. This spike must be limited within the absolute maximum
ratings (for example, adding a gate resistor in series to HS MOSFET gate, or a phase
resistor in series to PHASE pin), as well as the positive spike, but has an additional
consequence: it causes the bootstrap capacitor to be over-charged. This extra-charge can
cause, in the worst case condition of maximum input voltage and during particular
transients, that boot-to-phase voltage overcomes the absolute maximum ratings also
causing device failures. It is then suggested in this cases to limit this extra-charge by adding
a small resistor in series to the bootstrap diode (R
D
in
Figure 1
).
Figure 9.
LS DRIVER
Drivers turn-on and turn-off paths
LS MOSFET
L
C
IN
V
IN
UGATE
PHASE
LGATE
GND
LOAD
L6727
C
OUT
R
GATE
R
INT
C
GD
C
GS
C
DS
VCC
GND
LGATE
R
GATE
R
INT
C
GD
C
GS
C
DS
BOOT
HS DRIVER
HS MOSFET
PHASE
UGATE
R
PHASE
相關PDF資料 |
PDF描述 |
|---|---|
| L6730CQ | Adjustable step-down controller with synchronous rectification |
| L6730C | Adjustable step-down controller with synchronous rectification |
| L6730CQTR | Adjustable step-down controller with synchronous rectification |
| L6730CTR | Adjustable step-down controller with synchronous rectification |
| L6730D | Adjustable step-down controller with synchronous rectification |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6728 | 功能描述:DC/DC 開關控制器 Sngl phase PWM controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| L6728_0706 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Single phase PWM controller with Power Good |
| L6728A | 功能描述:電壓模式 PWM 控制器 Hi-Freq. singl-phase PWM controller w/Po RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| L6728AH | 功能描述:軟開關 PWM 控制器 Sgl Output 600 KHz DFPN-10 RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| L6728AHTR | 功能描述:電流型 PWM 控制器 HIGH FREQ PWM CNTRL W/PO RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。