參數資料
型號： L6585DTR
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： 0.6 A POWER FACTOR AND FLUORESCENT LIGHT CONTROLLER, 250 kHz SWITCHING FREQ-MAX, PDSO20
封裝： LEAD FREE, SOP-20
文件頁數： 13/25頁
文件大?。?/td> 1478K
代理商： L6585DTR
Re–lamp
L6585D
20/25
Table 7.
Fault conditions
Fault
Condition
IC behavior
Action required
Lamp absence
(re-lamp comparator)
At turn-on: EOL-R
voltage higher than
4.63V
–The TCH charge doesn’t start (no
ignition)
– Drivers stopped
– IC low consumption (Vcc clamped)
Lamp replacement
(EOL-R below 4.63V)
Run mode: EOL-R
voltage higher than
4.63V
– All drivers stopped
– IC low consumption (Vcc clamped)
End of life
EOL-R voltage outside
the limits of window
comparator
–TCH cycle
(1) (reset if the fault
disappears)
– drivers stopped at the end of TCH
cycle
– IC low consumption (VCC clamped)
Re-lamp cycle (2)
Half-bridge current
sense
Ignition:
HBCS threshold
–TCH cycle
(1) with lamp voltage
control
– In case of HBCS at the end of the
TCH cycle, drivers stopped
– IC low consumption (Vcc clamped)
Re-lamp cycle (2)
Run mode:
HBCSL threshold
–TCH cycle
(1) with lamp voltage
control (frequency increase)
– In case of HBCS at the end of the
TCH cycle, drivers stopped
– IC low consumption (Vcc clamped)
Re-lamp cycle (2)
Run mode:
HBCSH threshold
– Drivers stopped
– IC low consumption (Vcc clamped)
Re-lamp cycle (2)
Shut-down
CTR voltage lower than
0.8V
– Drivers stopped
– IC low consumption (Vcc clamped)
When the CTR voltage
returns above 0.8V, the
IC driver restart with a
pre-heating sequence
Choke saturation
PFCS voltage higher
than 1.6V
– Drivers stopped
– IC low consumption (Vcc clamped)
Re-lamp cycle (2)(3)
Over-voltage of PFC
output
CTR voltage higher than
3.4V
– PFC driver stopped
When the CTR voltage
returns below
3.26V (Typ.), the PFC
driver restarts
PFC open loop
(feedback
disconnection)
CTR voltage higher than
3.4V AND INV voltage
lower than 1.2
– Drivers stopped
– IC low consumption (Vcc clamped)
Re-lamp cycle (2)(3)
1.
TCH cycle: charge of the TCH voltage up to 4.63V and discharge down to 1.50V following the RDCD time constant;
2.
Re-lamp cycle: the voltage at EOL-R pin must be first pulled above 4.63V and then released below it; this typically happens
in case of lamp replacement. After a re-lamp cycle, a new pre-heating sequence will be repeated.
3.
This fault actually is a "board" fault so a lamp replacement is not effective to restart the ballast
相關PDF資料
PDF描述
L6590AN 0.7 A SWITCHING REGULATOR, 74 kHz SWITCHING FREQ-MAX, PDIP8
L6590D013TR 0.7 A SWITCHING REGULATOR, 74 kHz SWITCHING FREQ-MAX, PDSO16
L6590D 0.7 A SWITCHING REGULATOR, 74 kHz SWITCHING FREQ-MAX, PDSO16
L6591TR SWITCHING CONTROLLER, PDSO16
L6599AN SWITCHING CONTROLLER, DIP16
相關代理商/技術參數
參數描述
L6590 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:FULLY INTEGRATED POWER SUPPLY FIPS
L6590A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FULLY INTEGRATED POWER SUPPLY
L6590AN 功能描述:開關變換器、穩壓器與控制器 700 Volt Monolithic RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
L6590D 功能描述:開關變換器、穩壓器與控制器 700 Volt Monolithic RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
L6590D013TR 功能描述:開關變換器、穩壓器與控制器 700 Volt Monolithic RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*