參數資料
型號： L6563HTR
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： POWER FACTOR CONTROLLER, PDSO16
封裝： ROHS COMPLIANT, SOP-16
文件頁數： 26/48頁
文件大?。?/td> 1634K
代理商： L6563HTR
Application information
L6563H
32/48
Doc ID 16047 Rev 2
6.7
Power management/housekeeping functions
A special feature of this IC is that it facilitates the implementation of the “housekeeping”
circuitry needed to co-ordinate the operation of the PFC stage to that of the cascaded DC-
DC converter. The functions realized by the housekeeping circuitry ensure that transient
conditions like power-up or power down sequencing or failures of either power stage be
properly handled.
This device provides some pins to do that. One communication line between the IC and the
PWM controller of the cascaded dc-dc converter is the pin PWM_LATCH (Figure 47b),
which is normally open (high impedance) when the PFC works properly, and goes high if it
loses control of the output voltage (because of a feedback loop disconnection) with the aim
of latching off the PWM controller of the cascaded dc-dc converter as well (see “Feedback
failure protection” section for more details).
A second communication line can be established via the disable function included in the
PFC_OK pin (see “Feedback failure protection” section for more details). Typically this line is
used to allow the PWM controller of the cascaded dc-dc converter to drive in burst mode
operation the L6563H in case of light load and to minimize the no-load input consumption.
Interface circuits like those are shown in Figure 46.
Figure 46.
Interface circuits that let dc-dc converter's controller IC drive L6563H in
burst mode
The third communication line is the pin PWM_STOP (#11), which works in conjunction with
the pin RUN (#12). The purpose of the PWM_STOP pin is to inhibit the PWM activity of both
the PFC stage and the cascaded dc-dc converter. The pin is an open collector, normally
open, that goes low if the device is disabled by a voltage lower than 0.8 V on the RUN pin. It
is important to point out that this function works correctly in systems where the PFC stage is
the master and the cascaded dc-dc converter is the slave or, in other words, where the PFC
stage starts first, powers both controllers and enables/disables the operation of the dc-dc
stage. The pin RUN can be used to start and stop the main converter. In the simplest case,
to enable/disable the PWM controller the pin PWM_STOP can be connected to the output of
the error amplifier (Figure 47a).
相關PDF資料
PDF描述
L6563H POWER FACTOR CONTROLLER, PDSO16
L6565N 0.7 A SWITCHING CONTROLLER, PDIP8
L6615N 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8
L6711TR 2 A SWITCHING CONTROLLER, 178 kHz SWITCHING FREQ-MAX, PQFP48
L6711 2 A SWITCHING CONTROLLER, 178 kHz SWITCHING FREQ-MAX, PQFP48
相關代理商/技術參數
參數描述
L6563S 功能描述:功率因數校正 IC Transition Mode PFC 5mA 90uA 1.5% Ref RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
L6563STR 功能描述:功率因數校正 IC Transition Mode PFC 5mA 90uA 1.5% Ref RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
L6563TR 功能描述:功率因數校正 IC POWER SUPPLY RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
L6564 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:10 pin transition-mode PFC controller
L6564D 功能描述:IC PFC CTRLR TRANSITION 10SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - PFC（功率因數修正） 系列:- 產品培訓模塊:GreenChip Synchronous Rectification Control Family of ICs 標準包裝:1 系列:- 模式:間歇導電（DCM） 頻率 - 開關:- 電流 - 啟動:- 電源電壓:8.6 V ~ 38 V 工作溫度:-20°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:Digi-Reel® 其它名稱:568-5348-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*