參數資料
型號： L6226Q
廠商： STMICROELECTRONICS
元件分類： 運動控制電子
英文描述： BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32
封裝： 5 X 5 MM, 1 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-32
文件頁數： 26/29頁
文件大?。?/td> 480K
代理商： L6226Q
Pin connection
L6226Q
6/29
Doc ID 14335 Rev 5
Table 4.
Pin description
N°
Pin
Type
Function
1, 21
GND
Signal ground terminals.
9
OUT1B
Power output Bridge B output 1.
11
OCDB
Open drain
output
Bridge B overcurrent detection and thermal protection pin. An internal open
drain transistor pulls to GND when overcurrent on bridge B is detected or in
case of thermal protection.
12
SENSEB
Power supply
Bridge B source pin. This pin must be connected to power ground directly or
through a sensing power resistor.
13
IN1B
Logic input
Bridge B input 1
14
IN2B
Logic input
Bridge B input 2
15
PROGCLB
R pin
Bridge B overcurrent level programming. A resistor connected between this
pin and ground sets the programmable current limiting value for the bridge B.
By connecting this pin to ground the maximum current is set. This pin cannot
be left non-connected.
16
ENB
Logic input
Bridge B enable. LOW logic level switches OFF all power MOSFETs of
bridge B.
If not used, it has to be connected to +5 V.
17
VBOOT
Supply
voltage
Bootstrap voltage needed for driving the upper power MOSFETs of both
bridge A and bridge B.
19
OUT2B
Power output Bridge B output 2.
20
VSB
Power supply
Bridge B power supply voltage. It must be connected to the supply voltage
together with pin VSA.
22
VSA
Power supply
Bridge A power supply voltage. It must be connected to the supply voltage
together with pin VSB.
23
OUT2A
Power output Bridge A output 2.
24
VCP
Output
Charge pump oscillator output.
25
ENA
Logic input
Bridge A enable. LOW logic level switches OFF all power MOSFETs of
bridge A.
If not used, it has to be connected to +5 V.
26
PROGCLA
R pin
Bridge A overcurrent level programming. A resistor connected between this
pin and ground sets the programmable current limiting value for the bridge A.
By connecting this pin to ground the maximum current is set. This pin cannot
be left non-connected.
27
IN1A
Logic input
Bridge A logic input 1.
28
IN2A
Logic input
Bridge A logic input 2.
29
SENSEA
Power supply
Bridge A source pin. This pin must be connected to power ground directly or
through a sensing power resistor.
30
OCDA
Open drain
output
Bridge A overcurrent detection and thermal protection pin. An internal open
drain transistor pulls to GND when overcurrent on bridge A is detected or in
case of thermal protection.
31
OUT1A
Power output Bridge A output 1.
相關PDF資料
PDF描述
L6227N STEPPER MOTOR CONTROLLER, 2.8 A, PDIP24
L6228Q STEPPER MOTOR CONTROLLER, 2.8 A, QCC32
L6228QTR STEPPER MOTOR CONTROLLER, QCC32
L6229D BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO24
L6229N BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDIP24
相關代理商/技術參數
參數描述
L6226Q_10 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DMOS dual full bridge driver
L6226QTR 功能描述:功率驅動器IC DMOS Full Bridge Driver RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6227 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DMOS DUAL FULL BRIDGE DRIVER WITH PWM CURRENT CONTROLLER
L6227D 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L6227DTR 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*