- 您現在的位置：買賣IC網 > PDF目錄43899 > L6226D (STMICROELECTRONICS) BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO24 PDF資料下載
參數資料
| 型號： | L6226D |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO24 |
| 封裝： | SO-24 |
| 文件頁數： | 28/31頁 |
| 文件大?。?/td> | 525K |
| 代理商： | L6226D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁
Pin connections
L6226
6/31
Doc ID 9452 Rev 4
9
24
OCDB
Open drain
output
Bridge B overcurrent detection and thermal
protection pin.An internal open drain
transistor pulls to GND when overcurrent
on bridge B is detected or in case of
thermal protection.
10
25
SENSEB
Power
supply
Bridge B source pin. This pin must be
connected to power ground directly or
through a sensing power resistor.
11
26
IN1B
Logic input
Bridge B input 1
12
27
IN2B
Logic input
Bridge B input 2
13
28
PROGCLB
R pin
Bridge B overcurrent level programming. A
resistor connected between this pin and
Ground sets the programmable current
limiting value for the bridge B. By
connecting this pin to Ground the
maximum current is set.This pin cannot be
left non-connected.
14
29
ENB
Logic input
Bridge B enable. LOW logic level switches
OFF all Power MOSFETs of bridge B. If not
used, it has to be connected to +5V.
15
30
VBOOT
Supply
voltage
Bootstrap voltage needed for driving the
upper Power MOSFETs of both bridge A
and bridge B.
16
32
OUT2B
Power
output
Bridge B output 2.
17
33
VSB
Power
supply
Bridge B power supply voltage. it must be
connected to the supply voltage together
with pin VSA.
20
4
VSA
Power
supply
Bridge A power supply voltage. it must be
connected to the supply voltage together
with pin VSB.
21
5
OUT2A
Power
output
Bridge A output 2.
22
7
VCP
Output
Charge pump oscillator output.
Table 4.
Pin description (continued)
Pin n.
Name
Type
Function
SO24/
PowerDIP24
PowerSO36
相關PDF資料 |
PDF描述 |
|---|---|
| L6226PD | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO36 |
| L6226QTR | BRUSH DC MOTOR CONTROLLER, QCC32 |
| L6226Q | BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6227N | STEPPER MOTOR CONTROLLER, 2.8 A, PDIP24 |
| L6228Q | STEPPER MOTOR CONTROLLER, 2.8 A, QCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6226DTR | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6226N | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6226PD | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6226PDTR | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6226Q | 功能描述:功率驅動器IC DMOS Full Bridge Driver RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。