- 您現在的位置：買賣IC網 > PDF目錄384584 > L6208 (意法半導體) FULLY INTEGRATED STEPPER MOTOR DRIVER PDF資料下載
參數資料
| 型號： | L6208 |
| 廠商： | 意法半導體 |
| 英文描述： | FULLY INTEGRATED STEPPER MOTOR DRIVER |
| 中文描述： | 完全集成的步進電機驅動器 |
| 文件頁數： | 17/27頁 |
| 文件大?。?/td> | 453K |
| 代理商： | L6208 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
17/27
L6208
Figure 20 shows the Overcurrent Detection operation. The Disable Time t
DISABLE
before recovering normal oper-
ation can be easily programmed by means of the accurate thresholds of the logic inputs. It is affected whether by
C
EN
and R
EN
values and its magnitude is reported in Figure 21. The Delay Time t
DELAY
before turning off the
bridge when an overcurrent has been detected depends only by C
EN
value. Its magnitude is reported in Figure 22.
C
EN
is also used for providing immunity to pin EN against fast transient noises. Therefore the value of C
EN
should be chosen as big as possible according to the maximum tolerable Delay Time and the R
EN
value should
be chosen according to the desired Disable Time.
The resistor R
EN
should be chosen in the range from 2.2K
to 180K
. Recommended values for R
EN
and C
EN
are respectively 100K
and 5.6nF that allow obtaining 200
μ
s Disable Time.
Figure 20. Overcurrent Protection Waveforms
I
SOVER
I
OUT
V
th(ON)
V
th(OFF)
V
EN(LOW)
V
DD
t
OCD(ON)
t
D(ON)EN
t
EN(FALL)
t
EN(RISE)
t
DISABLE
t
DELAY
t
OCD(OFF)
t
D(OFF)EN
V
EN
BRIDGE
ON
OFF
OCD
OFF
ON
D02IN1400
相關PDF資料 |
PDF描述 |
|---|---|
| L6208D | FULLY INTEGRATED STEPPER MOTOR DRIVER |
| L6208N | FULLY INTEGRATED STEPPER MOTOR DRIVER |
| L6208PD | FULLY INTEGRATED STEPPER MOTOR DRIVER |
| L6210 | DUAL SCHOTTKY DIODE BRIDGE |
| L6213 | SOLENOID DRIVER SWITCH MODE POWER SUPPLY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6208D | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208D | 制造商:STMicroelectronics 功能描述:Supply Voltage Max.:52V |
| L6208D013TR | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208D013TR-CUT TAPE | 制造商:ST 功能描述:L6208 Series Dual 52 V 5.6 A DMOS Driver for Bipolar Stepper Motor - SOIC-24 |
| L6208N | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。