- 您現在的位置：買賣IC網 > PDF目錄97995 > L6207PD013TR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 5.6 A, PDSO36 PDF資料下載
參數資料
| 型號： | L6207PD013TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO36 |
| 封裝： | ROHS COMPLIANT, POWER, SOP-36 |
| 文件頁數： | 5/23頁 |
| 文件大小： | 387K |
| 代理商： | L6207PD013TR |
13/23
L6207
NON-DISSIPATIVE OVERCURRENT PROTECTION
The L6207 integrates an Overcurrent Detection Circuit (OCD). This circuit provides protection against a short
circuit to ground or between two phases of the bridge. With this internal over current detection, the external cur-
rent sense resistor normally used and its associated power dissipation are eliminated. Figure 12 shows a sim-
plified schematic of the overcurrent detection circuit.
To implement the over current detection, a sensing element that delivers a small but precise fraction of the out-
put current is implemented with each high side power MOS. Since this current is a small fraction of the output
current there is very little additional power dissipation. This current is compared with an internal reference cur-
rent IREF. When the output current in one bridge reaches the detection threshold (typically 5.6A) the relative
OCD comparator signals a fault condition. When a fault condition is detected, the EN pin is pulled below the turn
off threshold (1.3V typical) by an internal open drain MOS with a pull down capability of 4mA. By using an ex-
ternal R-C on the EN pin, the off time before recovering normal operation can be easily programmed by means
of the accurate thresholds of the logic inputs.
Figure 12. Overcurrent Protection Simplified Schematic
Figure 13 shows the Overcurrent Detection operation. The Disable Time tDISABLE before recovering normal oper-
ation can be easily programmed by means of the accurate thresholds of the logic inputs. It is affected whether by
CEN and REN values and its magnitude is reported in Figure 14. The Delay Time tDELAY before turning off the
bridge when an overcurrent has been detected depends only by CEN value. Its magnitude is reported in Figure 15.
CEN is also used for providing immunity to pin EN against fast transient noises. Therefore the value of CEN
should be chosen as big as possible according to the maximum tolerable Delay Time and the REN value should
be chosen according to the desired Disable Time.
The resistor REN should be chosen in the range from 2.2K to 180K. Recommended values for REN and CEN
are respectively 100K
and 5.6nF that allow obtaining 200s Disable Time.
+
OVER TEMPERATURE
IREF
(I1A+I2A) / n
I1A / n
POWER SENSE
1 cell
POWER SENSE
1 cell
POWER DMOS
n cells
POWER DMOS
n cells
HIGH SIDE DMOSs OF
THE BRIDGE A
OUT1A
OUT2A
VSA
I1A
I2A
I2A / n
OCD
COMPARATOR
TO GATE
LOGIC
INTERNAL
OPEN-DRAIN
RDS(ON)
40
TYP.
CEN
REN
ENA
+5V
C or LOGIC
D02IN1353
相關PDF資料 |
PDF描述 |
|---|---|
| L6219DSA | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| L6228PDTR | STEPPER MOTOR CONTROLLER, 2.8 A, PDSO36 |
| L6228DTR | STEPPER MOTOR CONTROLLER, 2.8 A, PDSO24 |
| L6234PD013TR | BRUSHLESS DC MOTOR CONTROLLER, 5 A, PDSO20 |
| L6237 | BRUSHLESS DC MOTOR CONTROLLER, 2 A, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6207Q | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Dual Bridge DRV 5.6A 0.3 Ohm 100kHz RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6207QTR | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Dual Full Bridge Driver 5.6A RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:FULLY INTEGRATED STEPPER MOTOR DRIVER |
| L6208D | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208D | 制造商:STMicroelectronics 功能描述:Supply Voltage Max.:52V |
發布緊急采購，3分鐘左右您將得到回復。