- 您現在的位置：買賣IC網 > PDF目錄43899 > L6206N (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 5.6 A, PDIP24 PDF資料下載
參數資料
| 型號： | L6206N |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 5.6 A, PDIP24 |
| 封裝： | POWER, DIP-24 |
| 文件頁數： | 5/23頁 |
| 文件大?。?/td> | 421K |
| 代理商： | L6206N |
13/23
L6206
APPLICATION INFORMATION
A typical application using L6206 is shown in Fig. 12. Typical component values for the application are shown
in Table 2. A high quality ceramic capacitor in the range of 100 to 200 nF should be placed between the power
pins (VSA and VSB) and ground near the L6206 to improve the high frequency filtering on the power supply and
reduce high frequency transients generated by the switching. The capacitors connected from the ENA/OCDA
and ENB/OCDB nodes to ground set the shut down time for the Brgidge A and Bridge B respectively when an
over current is detected (see Overcurrent Protection). The two current sources (SENSEA and SENSEB) should
be connected to Power Ground with a trace length as short as possible in the layout. To increase noise immu-
nity, unused logic pins are best connected to 5V (High Logic Level) or GND (Low Logic Level) (see pin descrip-
tion). It is recommended to keep Power Ground and Signal Ground separated on PCB.
Table 2. Component Values for Typical Application
Figure 12. Typical Application
C1
100uF
D1
1N4148
C2
100nF
D2
1N4148
CBOOT
220nF
RCLA
5K
CP
10nF
RCLB
5K
CENA
5.6nF
RENA
100k
CENB
5.6nF
RENB
100k
CREF
68nF
RP
100
CP
CBOOT
RP
D2
D1
C2
OUT1A
LOADA
LOADB
OCDA
OCDB
1
5
21
18
19
8
16
OUT2A
GND
PROGCLA
OUT2B
OUT1B
VSA
POWER
GROUND
SIGNAL
GROUND
+
-
VS
8-52VDC
4
VSB
VCP
VBOOT
C1
SENSEA
20
IN1A
IN2A
IN1A
IN2A
2
6
7
9
ENA
ENB
CENB
RENB
RENA
ENA
ENB
23
IN2B
12
IN1B
IN2B
IN1B
11
14
24
17
3
15
22
SENSEB
RCLA
10
CENA
PROGCLB
13
RCLB
D02IN1344
相關PDF資料 |
PDF描述 |
|---|---|
| L6208PD013TR | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO36 |
| L6208D013TR | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 |
| L6219R013TR | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| L6223 | STEPPER MOTOR CONTROLLER, 6 A, PDIP20 |
| L6225PDTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6206N_ | 制造商:STMicroelectronics 功能描述:Dual Full Bridge Motor Driver 48V 24-Pin PDIP Tube |
| L6206PD | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6206PD013TR | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6206Q | 功能描述:馬達/運動/點火控制器和驅動器 PowerSPIN 8 to 52V 5.6A 0.3 Ohm 100kHz RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6206QTR | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Dual Bridge DRV 8 to 52V 5.6A 100KHz RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。