參數資料
型號: L5986A
廠商: STMICROELECTRONICS
元件分類: 穩壓器
英文描述: 3.9 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
封裝: ROHS COMPLIANT, HSOP-8
文件頁數: 8/38頁
文件大小: 1067K
代理商: L5986A
Application information
L5986
16/38
Doc ID 14971 Rev 3
6.3
Output capacitor selection
The current in the capacitor has a triangular waveform which generates a voltage ripple
across it. This ripple is due to the capacitive component (charge or discharge of the output
capacitor) and the resistive component (due to the voltage drop across its ESR). So the
output capacitor has to be selected in order to have a voltage ripple compliant with the
application requirements.
The amount of the voltage ripple can be calculated starting from the current ripple obtained
by the inductor selection.
Equation 9
Usually the resistive component of the ripple is much higher than the capacitive one, if the
output capacitor adopted is not a multi layer ceramic capacitor (MLCC) with very low ESR
value.
The output capacitor is important also for loop stability: it fixes the double LC filter pole and
the zero due to its ESR. In Chapter 6.4, it will be illustrated how to consider its effect in the
system stability.
For example with VOUT = 3.3 V, VIN = 12 V, ΔIL = 0.75 A (resulting by the inductor value), in
order to have a
ΔV
OUT = 0.01VOUT, if the multi layer ceramic capacitor are adopted, 11 F
are needed and the ESR effect on the output voltage ripple can be neglected. In case of not
negligible ESR (electrolytic or tantalum capacitors), the capacitor is chosen taking into
account its ESR value. So in case of 330 F with ESR = 30 m
Ω, the resistive component of
the drop dominates and the voltage ripple is 22.5 mV
.
The output capacitor is also important to sustain the output voltage when a load transient
with high slew rate is required by the load. When the load transient slew rate exceeds the
system bandwidth the output capacitor provides the current to the load. So if the high slew
rate load transient is required by the application the output capacitor and system bandwidth
have to be chosen in order to sustain the load transient.
In the table below some capacitor series are listed.
Table 8.
Output capacitors
Manufacturer
Series
Cap value (
μF)
Rated voltage (V)
ESR (m
Ω)
MURATA
GRM32
22 to 100
6.3 to 25
< 5
GRM31
10 to 47
6.3 to 25
< 5
PANASONIC
ECJ
10 to 22
6.3
< 5
EEFCD
10 to 68
6.3
15 to 55
SANYO
TPA/B/C
100 to 470
4 to 16
40 to 80
TDK
C3225
22 to 100
6.3
< 5
ΔV
OUT
ESR
ΔI
MAX
ΔI
MAX
8C
OUT
f
SW
-------------------------------------
+
=
相關PDF資料
PDF描述
L5986ATR 3.9 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L5986TR 3.9 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L5986 3.9 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L5987ATR 4.4 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L5991D 1.5 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
相關代理商/技術參數
參數描述
L5986ATR 功能描述:直流/直流開關調節器 Step-down switch regulator, 2.5A RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
L5986TR 功能描述:直流/直流開關調節器 2.5 A Step-down Switch Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
L5987 功能描述:直流/直流開關調節器 3 A buck switching regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
L5987A 功能描述:直流/直流開關調節器 3 A STEP-DOWN SWITCH REG RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
L5987ATR 功能描述:直流/直流開關調節器 Step-down switch regulator, 3A RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5